I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hello
I’m aware that this topic has been discussed in several posts from a couple of years ago, but I haven’t found a concrete solution yet.
I'm currently using an external...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
Hi everyone, In the Power Management example, why the HFCLK still running when the uC is in sleep mode ? I see it in the HFCLK_STAT => State = 1 Shouldn't it be disable to...
Hello,
I have been using nRF development boards for a while, but recently I am currently unable to program my nRF52 development board, due to driver issues. The following...
I am trying to make TWI calls from an APP_TIMER event. However the TWI calls are failing. I can see that the twi message is sent on an oscilloscope, but the function never...
Hi,
I got the same error as the guy in this question: https://devzone.nordicsemi.com/f/nordic-q-a/26041/compiling-error-for-nrf51-development-dongle
I use another example...
Hi, I would like to use a nRF52 demo board, to test nRF BLE with a HX711 and screen. The nRF module is powered 3.3V but the HX711 and the screen are 5V powered. Is the bus...
Hello,
I am in the process of evaluating the '840's BLE and CryptoCell for a low power application. I am using a modified version of the ble_app_template example, with custom...
Hi guys,
I have custom MAC address that saved in the flash. I used the sd_ble_gap_address_set function to change the Mac address to my custom address.. I found out in phone...
Hello,
Is there any option in nrfjprog to force a Segger's JLink to power the target? I am able to turn the power-out feature on using JLinkExe buy I don't whether nrfjprog...
I refer to nRF52810 product specification v1.1 In all reference designs, C6 is N.C.
I would like to know why this is the case?
I would also like to know why it is included...
Hello,
I am using nRF52832 DK for my project which is to receive data from arduino and send it to a smartphone using BLE. My issue is that i make nRF52832 to enter Bootloader...
I have nRF52832 as my development kit. Currently I am testing various ble peripherals i.e Blinky , beacon etc. Now I have to test IR sensor with the Development kit .I aim...
Hello,
I used a the ble_app_template example to set up advertisements on the PCA10040 board and on our custom board. Both boards function and have good signal strength....
I build ADC example from SDK12.3.0 for nRF51822 QFAA chip from source. I used custom board and changed the pin configuration for UART logging in sdk_config.h file.
But unfortunately...
Hi All,
I am performing OTA-DFU - Generating our own packages on my nRF52DK. but when i am trying to generate zip but i am getting some error , below is the screenshot for...
The aQFN app note suggests a fully open paste stencil (opening size = pad size) for the center pad of the aQFN.
Our assembly house is suggesting a windowed paste stencil...
