Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
The " 5.3.6.8 Reset behavior " table in nRF52840 Product Specification v1.1 mentions that WDT reset does reset the WDT itself.
I'm trying to reconfigure the WDT after a...
Hello,
I am using HC-SR04 ultrasonic sensor and nrf52840dk. To measure the distance I have to find out for how long the ECHO pin of the sensor remains high.
for that I...
On my old Wondows10 development computer, all worked OK.
In a brand new Windows10 laptop, all up to this point installs/verifies fine using nRF Connect.
I cannot find...
Hello, I'm making a PCB project with nrf52832 and I want to use my debuggers only 2 pins(SWDCLK and SWDIO) to debug it. I have J-Link Edu, but I wonder if I can use it with...
Hi, All.
I' m studying nRF52832.
I have a question about example "ble_app_uart".
I m trying to send to smartphone using function "printf()".
Uart pins(RX, TX) are...
Hi everybody! I have a code running excellently on my nRF52840 DK. I would like to make it run on my nRF52840 dongle. What should I change in my SEGGER project? Can anybody...
I am building a project which requires accelerometer data from the LIS3DH accelerometer be read and then transmitted over bluetooth. I have successfully setup bluetooth transmission...
Hi,
For my project I need to receive 9 bytes of data from our main board. This data gets send using UART.
By looking at the pin diagram I could not find specific pins...
Hello,
I am running nRF Connect for Desktop v3.2.0 on Win10 64-bit machine. Everytime I launch an applet, such as Power Profiler, I get a new blank window and nothing happens...
Hi, I am having a problem changing information advertised by the Beacon while the application is running. I started with the app_ble_template example and added Information...
I have an nrf52832 dev board with me and I'm using nRF5_SDK_15.0.0_a53641a SDK version. I'm using the project " pca10040_ble " inside the " secure_bootloader " folder from...
Hello,
We are evaluating Thingy:91 for NB-IoT. We want to validate the RF transmit test and are using %XRFTEST command.
The syntax is as follows, AT%XRFTEST=1,1,3,18000...
The TWI_Scanner example is building and downloading fine (using SES) but it just prints:
"TWI scanner started."
Then nothing in terms of scanning addresses etc.
It does...
I've modified the ble-central/ble_app_rscs_c to scan for extended advertising packets.
The code works great on the nRF52 DK, but doesn't work on the dongle (nRF52840). ...
