I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
We are currently using an nRF53 in our plant sensor project, where we need to be able to enter sleep mode and be woken up via RTC and GPIO interrupt. Since the nRF53 does...
Greetings,
we developed a custom board with a NRF9160 last year to be used with NB-IoT (LTE-M as Fallback) to communicate over HTTPS with our Servers. Now this worked quite...
Hi guys,
For a client of mine I'm working on an openthread RCP implementation using a SolidRun N8 that contains the NRF52833.
I'm using ncs v2.9.0-nRF54H20-1.
The problem...
Hi. I had a working MCUboot configuration that I used in order to update both the app core and the net core as follows:
- Upload the app core image using mcumgr - Upload...
Hello.
I keep trying to control my GoPro camera via BLE. At first I tried to do it using the old sdk, but it didn't work ( devzone.nordicsemi.com/.../gopro-control-over...
Hello! I have a Nordic Power Profiler Kit 2 that I am using to make measurements on a project. The issue I am having is I get an error message when trying to connect the kit...
Hello All
We are trying to integrate ST7305 driver with NRF connecct SDK and are unable to get the driver to work using the extrnal module method mentioned in the NCS Intermediate...
My device tree overlay GPIO section looks like this:
Note that I repurposing a GPIO that was used for an LED in the board's device tree file. Also note that node numbers...
Due to production requirements, I need to obtain the device's QR code. However, I found that the QR code can only be retrieved using the code snippet below after calling Nrf...
Hello,
I am using the nfc_system_off example code to evaluate the characteristics of power off mode.
Current measurement is done by following the instruction shown in...
I am trying to use Health SRV and Health CLI to check if there are any errors in the nodes. I have successfully transmitted the fault codes, but there are still many questions...
Hello
I created the out of tree sample sensor application with SDK 2.6.2 and it built just fine However it builds only when it is inside the sdk that was pulled when I selected...
Hey everyone. I am having an issue reading the WHO_AM_I register from the stm lsm6dsv16x. I am using the spi1 configuration as shown in the academy classes. I have very short...
I am using an nRF52840 USB dongle to sniff some Zigbee packets for a product I am developing. I am trying to use Wireshark to decode the messages shared. I followed the steps...
Hi,
I'm using nRF9160DK with SDKs v3.0.0
I am trying to use A-GPS with nRFCloud REST. I used the location example and it works correctly. The documentation states that...
