I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
nRF52810 will not enter deep sleep (system level power management). The method used is through pm_policy_next_state, sleep entry function , sleep exit function, and PM notifier...
I have a brand new development board that is failing to flash the sample programs using nRF Connect Desktop quickstart (Linux/Ubuntu 24.04). Here are the logs:
2025-06-08T17...
nRF52810 board will not start on its own. It needs the RTT Viewer to be connected, then it will start and run. It has run on its own before with this configuration:
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
I've seen a few posts about this, but they are all old, and maybe don't apply to USB-C We have a device that already uses USB-C for battery charging. We want to carry the...
I was able to complie many of the nrfx/samples under SDK v2.5.0 using VS Code IDE but cannot successfully compile any under SDK v3.0.0 .
The [Building and running]: <.....
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
