Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
i make a project
Every 5 minutes, beacon advertising should be repeated for 30 seconds.
Using the RTC example, LED lights and turns off every 3 seconds were realized....
Hi Sir,
In the datasheet, the start up time of 32K LFXO is 0.25s.
What is the start up time of 32K LFXO at Low temperature (-40/-30/-20 degree)?
Thank you.
BRs, H...
I have successfully upgrade 2 thingy 91 with the latest modem firmware 1.2 via MCUboot, and it worked.
I then tried to upgrade the existing standard application from 2019...
The nRF9160 v1.2.0 does not respond "OK" after AT+CFUN=0 !!!
2020-05-07T12:21:07.489Z DEBUG modem >> at+cfun=0\x0D\x0A 2020-05-07T12:21:08.489Z ERROR Error: 'at+cfun=0
Hi Devzone,
I am a beginner in BLE development. I have a nrf52840-dk and want to test the ble-app-uart example in SDK-16.0.0.
I firstly use NRF connect desktop programmer...
Hi,
I recently procured a nrRF52 DK board (PCA10040, v2.0.0 with nRF52832) for our new product development activity.
I tried following precompiled binaries present in...
Dear Nordic Tech Support & community,
The SDK 16.0.0 supports only one button long-push at time. Attached you can find a SDK-patch to add the support of multiple long-press...
Hi Team
I am trying to implement the firmware upgrade for master controller nrf52832 on chip using esp8266 over uart and I am very new with this boot-loader part.
I...
Hi
I had implemented a DFU module in esp8266 where I am trying to upgrade nrf over serial (UART Communication).
I had success with Init file write but when I send the...
Hi,
I am using nrf52833 EVB as an SPI master. The data is sent properly and well-received at the slave, however, I have a problem with the data received.
The problem...
Behaviour:
- Bluefruit the feater (nRF82832)
- Bluetooth BLE
- Implementation of Fitness Machine Service (0x1826)
- What is correct : all characteristics notified...
Hello, Nordic!
Our project is at evaluation stage. We aimed to build an Bluetooth 5.1 AoA indoor locator system, where the reciever should know the location of the transmitter...
We are using nrf52840 USB dongle to get PIR sensor readings and send measurements over the Bluetooth Mesh Schematics are following: We increased power for peripherals to 3...
