the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hi,
I'm using NRF52832 SDK15.2 to develop a smart band. Each time reconnect with iphone, the application assert in the peer manager event handler pm_evt_handler().
Any...
Hi Team,
I would like to know what does the system do after I call system off function as per below:
I have check through the oscilloscope to check how's the system...
Hi Team,
I am in the UK and trying to get an evaluation sim from Vodafone for NB-IoT. However they have set a limit of 2 IP addresses and hence I need the IP address of...
I'm developing bluetooth logging software on the nRF51 DK using SDK 12.3.0. We had been developing for some time in mbed, but were advised to switch over to Keil using the...
Hi,
I'm working on sending reliable message from server to client, the models are modified from RSSI model.
When I tring to send messages to client it will keep sending...
I've been trying to store an array (SDK16,S332)
uint8_t my_data[]={0x00,0x01,0x02,0x03,0x04,0x05,0x06,.........0x23}
using fstorage I wrote an update function :
I hardcoded...
To the kind attention of Nordic support team,
I'm trying to do things like in https://devzone.nordicsemi.com/f/nordic-q-a/39630/windows-command-line-dfu-over-ble-with-pca10059...
Hi,
I have a project which was originally written using SDK12, and have updated it to SDK16, I am sorry I know this question seems to have been asked in many different ways...
Dear,
Like I said in the title, I did use the NFC of my PCA10056 with my phone, it works, I also can read some information from nRF52840 by NFC. Right now, I programmed...
Hi Devzone:
I am working on nRF52840 with latest SDK.
I have 1 differential pair and 1 single ended pin I want to sample, single ended samples at every 40ms while differential...
I was trying to connect my cellphone tu the ublox modulo for sends at commands from my cell, in the main program of the micro I've the next lines for turn on the ublox module...
i have a nrf52840 dk
i need to connect the flex sensor to the board and know the resistance value while bending
how to do it?
and what code should i dump
Hi there,
I have developed the custom board with nrf52832 Soc and programmed blink code, it works fine.Now i uploaded the ble DFU template example and updated firmware...
I can't install the tool chain.
Looks like I have to install something called chocolatey?
I can't install chocolatey. I tried the chocolatey website for help and was baffelled...
Hi, I am trying to debug the blinky project with Eclipse, openocd and st-link. No softdevice. This is the output I am using.
I am finally able to see the leds blinking in...
