Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I have successfully compiled the GPS sample. I am trying to program the device using SES and only beign able to do it when the device is previously erased with NRF Connect...
Hello,
I am using nrf52840 to communicate with PAC 1710 sensor via TWI interface. The nrf52840 is the master device and the PAC chip is the slave device. Without SoftDevice...
I just updated to Segger 4.42a to follow the recommendation in the release notes for SDK v1.2.0
When I do a rebuild the AWS fota sample I get linker errors as shown below...
Hi,
I have a Laird Development Kit for the nRF52840 (DVK-BLL654PA-R2.0) which I want to program. Unfortunately Keil uVision and nRFgo Studio have problems with programming...
Hi all,
Greeting of the day....
Here I am getting an issue with TWI interface. That I am using to communicate with sensor module with NRF52840.
The SCL------> p0...
Hi
I am currently doing a project based on the nRF52840 MCU and evaluation board
as part of my project, I have used the LPComp module, and set it up to trigger on rising...
I have updated to SDK V1.2.0 and the AWS FOTA fails to get an ip address. My version 1.1.0 AWS FOTA still works.
See settings and outcomes below
For v1.2.0
and...
Hi,
I have an application on NRF52840. I'm able to connect successfully to mobile devices, with min connection interval of 7.5 and max of 30.
However, when I try to...
Hi Nordic Devzone,
I am using the simple BLE blink peripheral example that simply advertises and blinks an LED. I am using the ble_app_blinky_pca10040_s132 example found...
The Interface MCU on my nRF52-DK (PCA10040) broke, I replaced it with the same part number (got it from the BOM) and now I am struggling to program it through the JTAG port...
How does one get Mesh Network Id and Mesh Network Name on a provisioned device?
So far I have looked through the Mesh SDK API documentation, but was unable to find an answer...
Hello all,
My project based on NRF52832 SDK13 has some bug I trying to solve. Some users of my product very rarly faces with problem of constantly rebooting NRF52. After...
Hi,
I am trying to perform ADC conversions controlled by Timer with minimal manual interaction. My goal is that every 2 seconds, the ADC takes 10 samples in quick succession...
I have a project using nrf52840. The nrf52840 communication with a nbiot mcu using uart port. In my project the nbiot download the firmware from server and send the firmware...
