I 've been working with the nRF54L15 for a bit now and it' s been great, but trying to get a bit fancy now and running into problems. I 'm developing with the latest NCS v3...
Hi.
I'm using nrf Connect SDK v3.0.1 and Zephyr v4.0.99 to implement a IoT device which connects to a Thingsboard server with CoAP. With the COAP_CLIENT Lib I want to download...
Hello,
I am testing the RF range of a BLE application based on PAwR (Periodic Advertsing with response) in coded PHY (S8) with SDK 2.9.0.
In order to test the robustness...
Hi all, hope this is the right place. I'm developing a small breakout board to test/program the NRF52805; this board will eventually be expanded to include a pressure sensor...
Hi
I can run the sample application for NVS, on the nF5340 DK (SDK 2.9.0)
I can run the sample application for LittleFS, also on the nRF5340 DK
Now I would like to see...
Hello everyone,
As the title suggests, we're trying to get the on board flash (mx25r64 as far as I can tell) of the nrf7002dk devboard working as a USB mass storage device...
Hello.
After some great struggles, we've managed to enable WiFi and encrypted socket + TLS connection to google.com and various websites.
Since then, we've been looking...
Hi I have had problems when trying to update the relay status of a server node in my mesh app which is a combination of the light switch server proxy and dfu examples (plus...
Hi!
We are using the nRF52840 and nRF52832 for a product for which good data throughput over BLE is required. (We have picked the S140 and S132).
We send these data using...
Hi,
I'm trying to use RTT Logging in my application. If I build and flash my application through Segger Embedded Studio RTT logging works. However If I use ARM GCC to build...
I'm not able to carry out monitor mode debugging. I'm referring https://github.com/NordicPlayground/j-link-monitoring-mode-debugging/blob/master/pca10040/s132/arm5_no_packs...
Hello.
I almost finish nrf52-quadcopter develop.
I want fly drone with mobile.
I want to confirm PID value from minum to maxium in mobile.
and I want to confirm your...
Hello Nordic team
I am working on nRF52840 DK, SDK-15.0.0 with ble_central example. I need to give support of DFU like we are doing with ble_peripheral example.
My question...
Hi, I have a question for you! Thank you!
My PCA10040 was not successfully connected to the computer.
The device manager of the computer did not show anything related...
Hi
i am using SDK15.0 .i have tested Secure Ble for firmware update. Its working with my public keys. i want to know is it possible to update firmware without Public key...
Hello,
I am trying to find the IP address of the devices.
Device: nRF52840 DK
Setup: Running virtual Ubuntu 18.04 inside Windows 10 (using VMWare).
I am able to connect...
Is there any recommended way to flash the nRF51822-CEAA-R WLCSP chip?
Should a PCB design have UART design for flashing the nRF51822 chip after it is soldered on? Or should...
Hi, My problem is: When I programing my board using existing hex from SDK, I have no problem. Program working great. But if I building my own hex (build without errors) and...
Hello,
I am using nRF52832. My GPS is connected to GPIO pin (15, RX) and (16, TX) of nRF52832. My TCA9535 is connected to GPIO pin (8, SDA) and (7, SCL) of nRF52832. TCA9535...
Hi all,
I am currently building I2C communication between nrf52832 and a stm32 chip, stm32 as the master and nrf52 as the slave.
The situation is the stm32 couldn't get...
