Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Dear Sir,
I am talking with respect to the ble_app_hrs example in the SDK 15 for nrf52832. I am using softdevice S132.
In the example the code is implemented such that...
For instance, if I wanted to download the firmware that comes on the nRF52840-dongle in order to then write it to a custom board with an nRF52840 chip on it (i.e. so that...
Good morning,
I can't import the nrf_serial library ( and nrf_queue ) on the ble_app_uart project, after that i compile, i read these errors :
linking... .\_build\nrf52840_xxaa...
Hi,
I'm using 2 nRF52832s in my project. One of them is connected to a PC serially and has NUS central running on it and the other nRF52 connects to this central. I was...
I have two 52840DK, which can be used before, but I took it out and used it today. The led light on the rear panel of the USB is not lit, and the computer can't detect the...
Dear Sir,
I was trying to implement the following scenario.
Multiple phones initiate the connect request to a single peripheral.
On peripheral search for the phone...
I would like to confirm that my hardware design is correct and in addition that I am following the correct procedure to place the nRF52832 to sleep to achieve the lowest possible...
It works with SDK v12.3 and soft device 3.0.0. Does not after porting to 15.2. This is a custom board (extremely common configuration with single 32Mhz crystal) that serves...
Hello,
(I also create an issue over Thingy SDK GitHub page - #29)
It seems to me that there is an issue about the usage of MPU-9250.
I motioned Thingy and I observed...
Hi,
I am trying to get DFU working on my PCA10040 board using SDK 14.2 and armgcc toolchain.
I have followed the instructions to set up DFU here:
devzone.nordicsemi...
Hi,
Whenever I call `nrf_malloc` with a parameter bigger than 32, the pointer remains NULL. I think it's related to some sdk setting but I couldn't find it.
Anyone had...
Currently, I am working with the Nordic SimpleOnOff Model of the Light switch in the Bluetooth Mesh.
I am good that the light in the mesh can be set on/off after Provisioned...
HI guys,
I am running a beacon based on the ble_app_beacon example. This works fine.
Next, I made a connectable GAP/GATT application to read and make some settings. This...
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.2.0/lib_timer.html?cp=4_0_0_3_51_0_0#lib_timer_debugging
The link to " Monitor Mode Debugging -...
I flashed the Mesh serial hex file on nRF52840 dongle. I can see my dongle on nRF connect mobile application but not on nRF Mesh mobile application. So do I need the development...
