Power profiler kit ii not supplying power and reading current correctly. A month ago, my power profiler kit ii was working fine.
The actual voltage supplied to the test...
Hi,
During our testing of the Zigbee NCP sample, we encountered some compatibility issues. We have flashed the NCP sample firmware onto an nRF52840 Dongle using SDK version...
I have a zephyr zbus project running on the nrf52840DK that’s working well. We want to port the project to the nrf54H20DK, but I’m having trouble seeing the log messages....
Hi all,
we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
Hi,
I am attempting to get Direct Test Mode working on my nRF54L15 while also having access to the normal BT stack.
Normally, if I run dtm_tr_init(), I can begin the test...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hi,
I am testing the Bluetooth function on my custom board with nRF5340 CLAA chip. I have tested the clock, I2S and SPI on this chip previously and they all worked perfectly...
Dear All,
Currently I'm developing a BLE module that will be useful by its uart service and will use nrf51822. Nordic provided an example based on sdk 6.1 for low power...
Hello,
I want to read data from mesh network (from all the servers) to send it to a gateway. I saw in the documentation that Provisioner s can be a part of gateway devices...
Hi all,
I'm trying to enable Bluetooth 5 extended advertisement in nRF52840.
Currently, I'm using Nordic SDK v15.0.0 and S140 Softdevice v6.0.0.
In order to init the...
Dear Nordic Support Team,
I want to send the new PCB layout for manufacturer but I am not sure that
I can use any pairs of pin for DFU over serial or not.
I want to...
Hi all,
I have a question regarding the BLE mesh specification. When you are transmitting data using advertising frames, how does it check if the transmission medium is...
Hello everyone,
I am working on DFU bootloader application for android and iOS (using Qt C++).
For android everything works fine, but for iOS I have problems.
In order...
for the mass production what is the best solution in order to flash the nRF52?
for the mass production can I use DK PCA10040 ?
The DK PCA10040 can be used for dubbug on...
Hi I'm using Keil MDK 4.7 with nRF5 SDK V15, both of the 2 SDKs are installed at C:\, and the Keil4 Nordic License has been installed. When I tried to compile one of the example...
Hi all,
Is there any possibility to intimate any documentation errors(spell mistakes, content doubts, etc) to nordic documentation team?
Thanks,
Sridhar
Hi,
I have used examples\dfu\secure_bootloader\pca10056_ble application and successfully updated two applications(heart rate and health thermometer) over BLE. In order to...
Hello, i' trying to measure the power consumption of the nrf52840 PDK. So far i have been able to measure the current. How can i go about measuring the voltage and is it constant...
Hello, I recently received a Thingy:52 and was able to connect to PC using J-Link. After uploading Heart Rate Monitor program Thingy is no longer able to be added using iOS...
Hi,
I am facing difficulties porting Mesh examples to IAR.
I am getting the following error : #error "Your compiler is currently not supported." during compilation from...
I'm working with nrf52 dk to read the sensor dht22. i need to follow this steps to make sure the sensor is ready to send data.
Wait until DHT responds and pulls the line...
The problem is that the load was made via application, using nRF Tools in the DFU option, since I wanted to understand what I did with the files and others, but now that I...
