Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
In the course of investigating higher than expected current consumption, I've been looking at nRF52832 errata, and one that I'm concerned about is #78, use of Timer STOP task...
Hello,
I have been trying to merge the pwm_library (or gpiote) with ble_uarte examples to have controle on the pwm signal through UART events
I think i merged correctly...
Hi everyone.
I'm trying to transfer new firmware over UART for just only one node in mesh network.
My node will connect to other wireless MCU(ESP32, ESP8266....) over...
I'm using FreeRTOS and trying to get push button events to fire. The events would fire if I held the button down long enough. I found out that the problem was that "FREERTOS...
Hi
I have a custom board implementation that operates as follows:
Monitoring an input pin waiting for low high transition, BLE advertising of device.
When input event...
I'm having trouble having multiple characteristics for my custom service. My main.c looks like this:
Even though I have 2 characteristics added here, I can see just the...
Hi,
I had a few nrf51822s lying around and as I find the chip and the SDK quite convenient to use, I thought about using them in a small MCU project which does not need...
Above you can see the original and commented out modified code for the given example. The modification causes crush to
NRF_BREAKPOINT_COND; // On assert, the system can...
Hi,
I was looking at the Thingy-52-to-nrf52xx demo. I want to capture raw motion data no a DK and save it for further processing. Are there any options (I guess one is nRF91...
hi
i read in earlier questions on the devzone that nordic offers to review the schematic and layout as well as perform tuning free of charge to their customer. Is that still...
Hello every!
I am testing FATFS example with nrf5284 PDK .
CLK - P1.15
MISO - P1.14
MOSI - P1.13
CS - P1.12
My micro sd card module work correctly with STM32 MCU. I...
Hi all,
I am Using SDK15, chipset is nrf52810 , In ble_app_uart application i have added the BLE_NUS_C and TWI application code , before this i have added only TWI to ble_app_uart...
This blog describes how to set up SES (Segger Embedded Studio) for use with nRF SDK:
https://devzone.nordicsemi.com/b/blog/posts/segger-embedded-studio-a-cross-platform...
i'm using DFU for my project, it worked fine until devices has been bonded , DFU cannot work again. i checked and find out that after running interrutps_disable() , the devices...
