Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Hi,everyone.
I had learn for below Links and compiling is no error.
https://devzone.nordicsemi.com/f/nordic-q-a/26448/nrf52832-maximum-number-of-central-links/104063#104063...
Hi,
I'm having problems to run the Loopback example in the Bluetooth Mesh SDK:
infocenter.nordicsemi.com/index.jsp
I'm receiving a timeout.
My setup is as follows...
This is a duplicate of https://devzone.nordicsemi.com/f/nordic-q-a/35127/spi-master-0-uses-300ua-upon-first-transfer but I wanted to be safe because I pre-maturely verified...
Hi,
I have been working on MPU9250 examples given in here .Though the program runs fine in KeilUvision 5, the output in tera term shows only 0,0,0 for Accelerometer values...
Normally one writes 0 to an event register to reset it.
I am writing a uart driver and when I open my interface I want to prime my transmit pump by setting EVENT_ENDTX to...
Hi all,
What are the default preflashed contents in the out of box nrf52840 flash?
I assume that bootloader is not present. If my assumption is correct how preflashed...
I'm looking at the SDK15 I2S example project using DMA. My dev set up is 52840/Keil.
The project is under: \nRF5_SDK_15.0.0_a53641a\examples\peripheral\i2s
In the callback...
I am new to BLE development, if that helps preface this question.
My goal is to get a BL652 module by Laird working with the BLE UART example from the Nordic SDK. I am using...
We are working on porting an MESH example from Segger to IAR.
We started with the BLE Peripheral Template, and pulled all the code for the light_switch_provisioner into...
Hi, I noticed that Silicon Labs announced their Mobile Mesh application for Android and showed a demo video .
I searched Nordic's GitHub page. However, I couldn't find...
While trying to make a custom server model, based on the on-off model in the documentation, the code breaks when receiving an incoming message. The problem is in the file...
Hi ,
We have designed an Nrf52832 customized board having 32mhz crystal but not having any low frequency clock. The board is working fine with the blinky and other codes...
Hi,
I want control my gpio P0.06 to enable mcp16251, which is a regulator provide power to the nrf52832,
when i trying to control the mcp16251, i found that the gpio can...
Hi,
I'm having some issues getting the ble_app_hids_keyboard example working on Windows 7! While I can pair and connect from Windows 7 the Bluetooth HID driver fails to...
