After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hello, I'm new to Nordic boards.I would like to measure the bit error rate for a BLE link using nRF52840.
Is there any way of modifying any of the existing examples to add...
We use iOS nRF Connect primarily for DFU updates and find a real annoying issue with its behavior. We see this problem behavior on both v1.8.5 and v1.8.2, on both iPhone and...
Dear All,
Brief about the requirement:
ToF (Time of Flight) value computed is inclusive of the overhead delay of notifying to the application layer in the BLE stack...
Is it possible to use app_timer with the mesh stack?
Up to now I was not able to integrate the app_timer library into my build.
Can you give me an example how to integrate...
Hello Everyone,
I'd like to know if it is possible to use nfc to collect bonding informations from a smartphone. Then I'd like to transmit these informations to other devices...
Hi, i'm using nRF52 DK to communicate CX93510 encoder chip via SPI. I'm using nrf_drv_spi library with SPI0 connected to pins:
#define CX93510_MISO_PIN 22 #define CX93510_MOSI_PIN...
Hello all, I'm working with construction like:
To pass some data between APP and BOOTLOADER. At first I tried to place this buffer to the end of RAM, but after restart content...
Hey Hi all, I am new to BLE Technology and it's programming. Well, I need some help on my project that I am working on. I have multiple (=25) peripherals and I want each peripheral...
I've got a custom board using the NRF52810 with SDK v15.0.0.
I am using the TWIM driver (nrfx_twim.c master mode) to drive an LCD driver IC, a capacitive touch sensor IC...
hi , endnode, I has changed app_util.h as this link
https://devzone.nordicsemi.com/f/nordic-q-a/26448/nrf52832-maximum-number-of-central-links/104059#104059
the max link...
Hi,
Is it possible to use variable Read/Write twi data length?
I'm using:
nrf_twi_mngr_transfer_t const i2c_write_raw_transfer[1] = { //NRF_TWI_MNGR_WRITE(I2C_HUMIDITY_SENSOR_ADDR...
I'm looking for someone to hire to make a Thingy program for me.
I'd like to program the Thingy so it picks up ANT+ MO2 data or other ANT+ data from multiple sensors and...
Hello,
I would like to use the bouttonless dfu feature in my application, but I have not been able to run the sdk example ble_app_buttonless_dfu.
The application does...
Hi
I have query on glowing multiple LEDs example 8 LEDS with GPIOs of nrF51422
So went through nRF51822 series based EDK design files and i see they use 4 LEds to which...
