Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello,
I am working on ota ble_secure project. I have created a zip file which is the last step and copied this file to my smart phone so that I can upload it using nrf toolbox...
Apparently you need to set the CCCD handle of your target characteristic to enable notification. Problem is, how do you do that? I now know at least 2 ways to do that, one...
Hello!
I am using application that support ANT+ and BLE, so i am using s332 softdevice.
now I want to add BLE bootloader feature. (send .bin via BLE). but in SDK v12.2.0...
I am using the nrf52 development board, when I try to connect to one of its pins a signal from a sensor that generates an interrupt signal every 1ms the programs stops or...
Hi,
I have relay board which is attached to the SoC module nRF9E5 and also microchip serial SPI EEPROM 25AA320 is also attached.
I have the EEPROM programmer and I am...
Is it possible to connect more than one device over bluetooth to single router (Raspberry Pi 3 under archlinux)?
I connect using commands:
echo "connect 00:4D:25:16:1A...
Hi Nordic team!
In my company project, we are using the NRF52, and, apart of other peripherics, we need to use the NFC.
As the NFC isn't always exchanging data with the...
Hi all, As I known sdk13 have bluetooth 5 features that means we can send more than 31bytes in advertising data (8xdata) right? I'm using nRF52832 and softdevice s132 v5.0...
hi,
i'm not able to have the nRF24LE1 go to sleep. I'm using the example at the link below, to which I've added code for UART and ADC usage. Is there a way to end the...
hi
i am working eclipse for setting up projects for nrf52832. When i build the blinky example there is no error but the headers nrf_delay.h are not include and the LED_LIST...
Hi,
I want to write flash using received data in BLE interrupt handler(on_ble_evt()).
When i received some data from BLE, i try to write it to flash and wait until done...
Hi
I'm trying to use the nRF52840 USB Serial UART device (aka USB CDC ACM) however I can't find a Windows driver for this device
The VID is 0x1915 and the PID is 0x520F...
I need to copy a string, but i don't know how to define nor how to copy.
This is the string that i have to copy dev_name.p_data.
I use soft device S130 in NRF51
