Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Does the NRF51 DK come with a SWD interface connector-cable to plug into a PCB's SWD port when flashing/programming code into a WLCSP chip soldered onto the PCB? If not, are...
I'm trying to setup a simple host node to broadcast a attention message with no definitive destination node. I need any of the child nodes (primarily asleep) to see and process...
Hello everyone,
I tried to use the example project " ble_ant_app_hrm" SDKv14.2 but it doesn't work. The bluetooth connection work correctly, I connect my smartphone with...
Hello Nordic
I am developing our device. It uses SDK 14.2.0 and s332 SoftDevice.
This device communicate our app by using ble as peripherals.
I thought that our project...
Hi,
do the AES CCM module, AES ECB module, and the Cryptocell 310 (in nRF52840) employ measures against side channel attacks? I am mainly concerned with timing analysis...
Hi all,
I'm working with nRF52840 PDK and I'm using the last SDK and SoftDevice version: SDK v15.2.0 and SoftDevice v6.1.
I'm using the scanning module introduced in this...
hi
I am using nRF52832.i have added 3 service and and 3 characterastics to one service
1.Peripheral service (accelormeter + gyroscope sensor) and 3 characterstics
2...
Hi, Nordic team. I'm planning to create an iOS 11 BLE app.
I want to create a BLE app that can approximately depict indoor locations after the iOS device scans BLE beacons...
Hello,
I am thinking of using Thingy52 for my project. Before I order Thingy52, I would like to make sure if it will workout for my project.
(1) I wonder if data collected...
I am experimenting with light_switch server example from mesh SDK 2.1.1 . I want to add UART functionality to this example.
I referred to the ble_app_uart example from sdk15...
after cmake -G Ninja ..
-- SDK_ROOT=C:/BLE/SDK/nrf5_SDK_for_Mesh_v2.2.0_src/../nRF5_SDK_15.0.0_a53641a --- set with command line ARG -- PC-Lint executable not found. Linting...
Hi ~ SDK: nrf5_SDK_for_Mesh_v2_0_1 's ligth switch proxy client & proxy server IDEs : SEGGER Embedded Studio for ARM Release 3.40 Build 2018052200.36079 Windows x64 SoftDevices...
I'm looking for the nRF5x SDK v14.2.0-SR3 tha is written on the Smart Remote 3 for nRF52 user's manual. I could not find it on the DevZone, https://developer.nordicsemi.com...
Hi,
I am developing software supporting LEsecure using SDK 12.3 with nRF 51822.
Please tell me what to do when incorrect data is entered in "Passkey entry".
Currently...
Hi.
I've been trying to send a payload with STM32F but I can not. I've used both STM32F103 and STM32F3 to send a payload but neither of them worked. However, when I use...
