Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I've put on the stock dfu/bootloader_secure on the nrf52 DK.
I've then create a distribution ZIP and upload a blinky app to the DK. That worked fine.
Then I compiled...
Hi,
I have problem with DFU for 51822xxAB witch has 128kB flash.
I use dual bank bootloader for nrf51422xxAC witch has 256kB flash memory within nrf51822xxAB.
Ofcourse...
I know this might be a dumb question to you all, I am first time doing this sort of work
How to connect Jlink to NRF52? I need to flash a custom built BLE board with new...
I'm running on a nrf51822 chip, using Keil and a JLink Segger programmer. I'm running on SDK 12.2.0 and I believe I was correct in choosing pca 10028 s130 but I'm not 100...
I followed the instruction and installed the latest version of nRFgo 64bit v1.21.2. After installation, I can not find ble-sniffer___SNIFFER.zip at all.
Where can I find...
Hello,
I was able to get SEGGER_RTT_WriteString() to work correctly, however SEGGER_RTT_printf keeps giving me this issue when compiling:
._build\nrf52832_xxaa.axf:...
I am programming a beacon, first I had some problems using sd_ble_gap_adv_start() so I changed to ble_advertising_start() .
Now I have a problem when compiling:
_build...
I'm trying to use the PPK with an nRF51 dev board, and I'm getting this output whenever I try to start the PPK Software:
Checking installed packages
pyside: 1.2.4
pyqtgraph...
I tested a 23byte data transition in iPhone 5s with Softdevice 3.1.0, sdk12.2 .
it is ok. I know that iphone 5s is ble 4.0.
So I thought it would be possible on Android...
How do I set TIMER2 to interrupt every 1 ms?
Sounds like a very basic question, but I haven't succeed. For TIMER1 I can get it working, but for TIMER2 the highest frequecy...
I am using SAADC and reading in 1 analog channel. The data sheet says that scan mode is enabled when 2 or more channels are turned on. What if I am only using 1 channel ?...
Hello, after I program bootloader, sd, application, I did the following command to do read back protection,
nrfjprog --rbp ALL -f NRF51
But, even though I still can...
Is there a way to achieve what bsp_event_to_button_action_assign(button_id, action, event) does but using my own button?
The functions requires a button_id like 0,1,2,3...
When I use NRF_LOG_GETCHAR() witn nRF52 DK and onboard SEGGER UART it stops in next NRF_LOG_INFO(). Also after ARM reset it keeps in this error state. It seems that SEGGER...
Hello,
I'm trying to install wireshark sniffer on ubuntu 14.04 with PCA10031.
I follow this guide : devzone.nordicsemi.com/.../
But when I launch sudo python example_linux...
