Hello dear fellow developers,
I am solving the problem of how to add another peripheral to the project.
I would like to know a universal procedure for adding any peripheral...
Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
I'm using the nRF52840-DK part number 1490-1072-ND I ordered last week. In both nRF Connect for Desktop and the VS code extension the device wasn't able to detect. Tried two...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
In the documentation for the secure bootloader, it's mentioned that the provisioning data gets stored in OTP memory for some chips (e.g. nRF5340). Is there a way to know what...
Hi:
I don't receive any messages in the console during any of the exercises in Lesson 3 and Lesson 4 of the nRF Connect SDK Fundamentals.
No errors occurred during the...
Device Overview
We have developed a smart wearable that sends notifications to our mobile application over BLE. Under normal conditions, the device alternates sensor...
Hi all,
I have been stuck trying to debug the example project for a couple of days now and could not find the answer through searching. Here are my problems.
Background...
Hi All
I have a bunch of nrf51x22 (4,8) and I'd like them to read their own firmware data and send this to others that are in DFU mode using the over the air (OTA) method...
Dear Nordic Developer Zone,
I'm using nrf51822 EK testing the GPIO sense function. The code I'm using is based on what a nordic employee has posted elsewhere in this dev...
hello,
i was trying to compile the softdevice s130 example code given with softdevice download from nordic.
I am using the ARM-MDK lite 4.74 version. It is showing error...
My design goal is to conserve as much battery power as possible on a device that typically gathers data 30 to 40 minutes per day. To that end, our thought was to make the...
hi~
6.2.1
Updated Setup_JLinkARM_V490e to Setup_JLink_V492
Updated nrfjprog to version 5.2.0 (see own release notes for changes)
where is release note ??
i can...
Dear all:
I want to constantly transmit messages from a nRF51422 to an other nRF51422 with specific ID by ANT protocol. Then, I want to receive the messages from one to...
Hi,
I want to build a Tx that can reconfigure a channel(like change the device's number) after finding out a long time failed to send message.I use the way below:
sd_ant_channel_close...
hiii...
i hv made a custom profile with concurrent broadcast feature tested in master control panel and some other phone app... working properly.. but wen i tried in iphone...
Hi,
I try to open ANT+ channel and make sure the status is searching or tracking,
but if I use pstorage to update flash in the same time,
It will response timeout...
We are developing a keyboard for smart phone or plant and what to make different surpport for different device.
So can I make difference from ios device and Android device...
Please indicate me if there is a data port on nRF8002 after you burn out OTP, Can I use this I'c for data transmission. Please indicate communication port for this chip. Also...
Hi,
I'm testing ble_app_proximity example (...\Nordic\nrf51822\Board\nrf6310\s110\ble_app_proximity). I'm using Master Control Panel Android app version 2.0.3 and Nexus...
I'm using S110.
I have a characteristic that is writable from phone client. However, the characteristic has lower and upper limits (an acceptable range) for the application...
Hi experts,
I'm trying to bond device between my android phone and the Nordidc51822(S110 v7.0). but I found that it's very difficult to achieve this function. Is there...
