Hello Nordic community,
I’m working on a project with the nRF52840 DK (PCA10056) using the nRF5 SDK and the S140 SoftDevice. My goal is to:
1. Read two NTC thermistors...
I am trying to write SPI code for the nRF52840 dongle. Since the nRF5 SDK does not directly provide an example for the dongle, I followed the steps defined in this tutorial...
I am trying to build using a custom board and 2.9.1, but am getting these errors:
My dts looks like this:
I have the width specified. Much of this is over...
Hi everyone,
I'm developing a BLE application where I measure throughput between an nRF5340DK acting as peripheral and an nRF52 Dongle as the central (using a Python script...
Hi Nordic Team,
Previously, with the nRF52840, we could use the internal ADC channel to directly measure the supply voltage (VCC) for battery monitoring without external...
Hello, we are developing a BLE application using nRf52833. Because of the waterproof & stainless steel casing requirement with rechargeable battery charging capability, we...
Hello,
I am working with the NRF5340dk, nrf7002ek, and PPKII. I am unable to get the DK to power up with the PPK. I used a knife to break the trace but for some reason...
Hello,
I do erase flash pages in my application I use the sdk api:
nrf_nvmc_page_erase(firstaddress);
nrf_nvmc_write_bytes(address, data, len);
but I did not found...
Hello,
i couldnt find the correct answer yet. I would like to use a RTC and also the s110 and BLE.
I collect data from sensors over i2c and send it over BLE. timing...
My username and password credentials do not work here or on the normal nordic semi site. The random password (i.e. fj[k%3) will work at the nordic semi site, and continue...
Hi,
I am starting development on my project using the ble_app_hrs as a template. This project already has the buttons setup for interrupts using the Button Handler library...
Hi guys
I use gazell protocol for my application. I want to try some other way to decide the channel tables. So I decided to monitor the RSSI and chose the channels in...
Hello, I want to be able to perform actions in my app based on the tactile buttons being pressed on the beacon. When I bought it I was under the impression that the service...
Hi,
I have some problems to advertise a custom 128bit UUID.
I succeeded to set the 128bit base UUID and my Characteristics UUIDs are 128bits.
But how I can set the PrimaryService...
Hello,
I want to implement device pairing, using the pairing bit. The pairing bit is set in the masters device type. For a slave to pair with such master, it opens a channel...
Hi Nordic!
I am using nRF UART2.0 and nRF51822.
I am sending some data from nRF51822 to nRF UART2.0
But after 3 minutes, I can get disconnection.
and 0x16 error...
I am currently using ARM's CMSIS-DAP interface to support flashing of an nRF51422 from a host MCU (i.e. to perform updates of the SoftDevice and/or application code running...
Hi guys,
I have a custom hardware with the nrf51822 and we have a slow connection and services discovery is clearly slower that when we run the code in the Development...
I use two nRF24LE1s as transmiter and receiver Here are my questions:
I set the transmiter side to auto reply mode using PIPE0 ,but i found the STATUS regesitor to...
Hi I am trying coding a remote controller using nrf24le1 but failed. any sample code?
it with several keys when push down the pin will connect to GND.
when any key push...
Hi all,
I would connect the NRF8001 module to my microcontroller (SAM3SD8C). Does anyone have an example code for this microcontroller?
Otherwise is possible to modify...
