I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
A multiperipheral connection to a central, all with custom nordic devices (nRF52840) has been stablished. Comunication and connection work just fine, but after a synchronization...
Hi ! I am represnting company responsible for fruitymesh ( https://github.com/mwaylabs/fruitymesh ) which is an open-source proprietary ble mesh running on nrf5 chips. For...
Dear Support,
I have adjusted the radio test example in SDK16.0 for my custom hardware application using the nRF52840. I have followed the instructions on this page to...
To the kind attention of Nordic support team,
As it was said https://devzone.nordicsemi.com/f/nordic-q-a/57531/sdk16-nrf52810-secured-gazell-keil
the secured gzll library...
Hello,
I'm able to program the code (below) to the nRF52 DK. Leds 17 & 18 are working.
I'm unable to program the code to my custom board. Leds 9 & 10 are not working ...
Is there any problem with beacon advertisment and ADC? I have 3 adc pins configured to measure three different sensors... When i use UART over BLE... everything is ok.. but...
Hi!
I seen video and read manual how to use it, but still not doesn't work.
PPK + PCA10040
on the PPK board I set jumprs to DK (all 3 pcs). USB connected to PCA10040...
Looking through the datasheet, current consumption is provided for the nRF9160 Modem at 3.0V and 3.5V. Is it possible to get information on 5V related current draws? I've...
Hi,
I am using the example nrf5-ble-mpu-simple from nrf5-mpu-examples-master to do the following:
a) send a BLE beacon advertisement (non connectable)
b) periodically...
We are currently having an issue with DFU failing on Samsung A7 a running andorid 6.0.1. We are using nRF Toolbox for BLE (DFU application) and when I try to connect the device...
Good day!
I'm working on Time model fro Bluetooth specification.
Question is about time handler. I can't figure out should I write a separate handler for TAI, or I should...
Hi!
I´m currently using the nRF52840 demo board to determine the bluetooth range of the device I'm working on.
The question is: which is the orientation of the antenna...
Hi
We are using PCA10040 for a development and we are using P0.8 , we were setting it up to be No connect when low (IE Open collector) but it was being driven high and we...
