Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
I'm migrating my code from the MESH SDK 3.1.0 to 4.0.0 I'm using the following function to initialize a persistance storage controller
The new SDK doesn't use the ACCESS_FLASH_PAGE_COUNT...
Hi,
I have 2 or more Thingy52 [SDK13 SD s132 v4.0.4], both of them are sending beacon every 200ms.
They have also the scan active, so they are able to detect the other...
I have merged two program SPI slave and ble_app_uart
I am getting these two errors
undefined reference to `nrfx_spis_buffers_set'
undefined reference to `nrfx_spis_init...
Hello,
I'm using nRF52840 dongle. I implemented a virtual COM port to send messages to my computer. My problem is that I can send messages only if I'm already connected...
Hello everyone, I ask for help to install the new version of SES in Ubuntu Linux 18, since the license is not recognized by the em nor the hardware, I can program the card...
After enter low power mode I aim to config to wake up on a 1 sec timer, but in 20 us the event 0x26 comes. I cannot find what event ID 0x26 is and how to disable it ?
Info...
I am having an issue when building the hci rpmsg example for the following youtube tutorial
Zephyr RTOS and Bluetooth LE on the dual-core nRF5340
I've tried figuring this...
Hello,
According to the description in below page, " The image can be an application image, SoftDevice image, bootloader image, or a combined image of bootloader and SoftDevice...
I am trying to interface adxl362 sensor with ANNA-B112 evaluation board.i am trying to read the part id to check the connection. The code is pasted below.
nrf_drv_spi_config_t...
Hi! I am using the 52840-DK dev board.
I want to use two pins, P1.0 and P1.1 as GPIO output pins.
In my code I have;
nrf_gpio_cfg_output(BLE_CONNECTED); nrf_gpio_pin_clear...
Hi everyone,
I want to serial print three float values (x,y,z) from an IMU. I use the MACRO NRF_LOG_ERROR( "Float_Value: " NRF_LOG_FLOAT_MARKER "\r\n", NRF_LOG_FLOAT(value...
Race condition in starting the ADC following calibration. I am trying to start the ADC in the interrupt routine when the end calibration is reported, however I have unreliable...
Hello,
I have two brand new nRF52 DK eval boards version 2.0. On both boards, the reverse charging diode D8 is missing. That diode is required to power the board externally...
