I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
Hi,
As well know, the nrf52832 had build-in a battery level detect function. It can get battery-level by following program
Would you please tell me how to design it...
Hi
When I finished the program and read back, I saw that there was unintentional data at 0x2D000 and 0x2E000.
I used up to 0x26000 addresses. Where is this memory used...
I've taken the basic examples/peripheral/blinky code and tried to add the logging module to it. For some reason the only time I can get the application to run and log correctly...
I am developing a firmware application that needs simultaneous central and peripheral role. I am using sdk 15.2.0 and was experimenting on dev board PCA10040. I have taken...
Hello,
I want that nRF9160 goes into PSM on boot until a button is pressed, do someone have a good link about PSM please ?
How can I do a software reset with a clean lte...
Dear people,
I use a pca10056 (alternatively the pca10059 dongle) and have compiled the connectivity firmware as described on the github page (release 4.1.1).
The only...
I use nrf5_SDK_for_Mesh_v3.2.0_src\examples\serial and board pca10040.
Supported commands.
In [2]: for i in range(0, 10): send(cmd.Echo("Hello: " + str(i))); time.sleep...
Hi, I'm reading the nRF5340 OPS v0.5.1 document and in section 3.2 ("Memory") there is a reference to "256kB of peripheral RAM". However, the document doesn't explain what...
Hi there,
I'm working on nrf82382, try to use COMP function to monitor the voltage of AIN0(p0.02), but seems not working, no example for the COMP. and then I found the...
We enable TX notification of NUS service with bonded iOS (iPhone), iPhone constantly sends TX_READY command until disconnect.
Can you confirm this is correct behavior. ...
Hi, I am working with the adxl362 sensor and the nrf9160 SPI example ( https://github.com/Rallare/fw-nrfconnect-nrf/blob/nrf9160_samples/samples/nrf9160/spi/src/main.c ) and...
Hi, I am working with the adxl362 sensor on the Thingy91 and I want to set the trigger of the sensor to a specific value.
In the datasheet ( https://www.analog.com/media...
Hello everybody! I'm developing an application using CMSIS DSP library, so i included about 20 math files and using finctions from these files. After compiling i get a linker...
Hello Devzone,
I'm designing a custom board solution that drives a motor using a nRF52832. The board is powered with 4 x AAA batteries and a 2.5V LDO (STLQ50C25R) is used...
