Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello.
I'm reading the documentation of the radio peripheral of nRF52832 but I can't find any information about the S0 and S1 fields.
What are those fields? What do they...
Hi, guys. I'm using the PCA10056 and the SDK 15.3's BLE UART peripheral example. I'm working on a PWM controller using the mobile app.
I need to create a delayed PWM signal...
My current project is to build a simple BLE LED controller. The goals of this project are to familiarize myself with lower level modules and to practice designing/building...
Hello,
I'm trying to create a project from scratch and write my own drivers. I have strong background in C but unfortunately I don't know anything about assembly. I could...
Very strange, I have lots of nRF52x experience, but this one has me stumped.
Successfully updated our custom board/application from nRF5_SDK_15.0.0 to latest as indicated...
Hi all, I apologise for this very basic question, but I don't understand how to add/enable RTT debugging to my code. I want to practice writing basic code for the NRF5 SDK...
Could you please advise me regarding BLE security?
For security purposes, UUID data shouldn't be included in the advertising data package?
If we don' t put UUID in the...
Hello
My custom board has only 1 button and I'm trying to detect 3 button clicks. The first click is waking up the device and the other 2 are configured as BSP_EVENT_KEY_0...
I have a setup similar to this
When the callback is executed, the execution will enter the inbuilt_key function and then the output will stop and the execution will halt...
I'm using v1.2.0 for the nrf project and I am fairly confident I am using modem firmware 1.1.1 (though I don't know how to verify that).
I'm basing my project on "cloud_client...
Hi,
I am evaluating the ble_app_hrs_pca10056_s140 project with nRF5SDK160098a08e2 Dev kit and nRF82540 dev board.
I have put a breakpoint in line:
*p_erase_bonds = ...
Goodmorning,
what is the maxium current output for SPI pins on the nRF24LU1? The datasheet say "IVDD External load current" of 2mA, is this refered to the internal regulator...
In the documentation of the nRF SDK for Mesh v4.1.0 is written: "The following figure demonstrates how the data packets flow between mesh nodes and their layers within the...
Hello
Beacon using timeslot API
I am trying to implementing a beacon functionality using your timeslot API.
The beacon shall run in parallel to the normal SoftDevice...
Hi all,
In our application we have a piconet master (acting as GATT client) and several piconet slaves (acting as GATT servers). We have only limited time on the channel...
