Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello Nordic DevZone community,
I have been working with the ZBOSS stack on the nRF5340 and understand that it has version management and migration features for persistent...
Hi,
When I looked at the SPI lines using the oscilloscope, I saw that the MISO line had the same signal as the MOSI line. As you can see from the image, basically SPI configuration...
SDK 2.3.0
We have a custom board with a few GPIO connected to various interrupt sources (Button, sensor interrupts, power connection etc.)
We are experiencing here sleep...
nrf52820 custom board
nRF5_SDK_17.1.0_ddde560
s112_nrf52_7.2.0_softdevice
secure_bootloader_ble_s112_pca10100e
I tried to incorporate ble dfu to my application but...
Hi Team,
Excuse me. Where can I find the reliability test reports of the following four models? Thank you!
nRF54L15-QFAA-R
nRF9151-LACA-R
nRF7000-QFAA-R
nPM1100...
Hello,
I'm sure you know this already, but there seems to be a problem with the subject footprint. I guess I'm posting this to confirm that it in fact does have a bug in...
Hi,
Is there any sample code that can check the Ion_idle8 current below?
I am currently evaluating the following currents on a custom boat and it is running at around...
There are two NUS services here, but only the second one can send data through the RX characteristic. I've checked the source code and nothing has changed. How do I delete...
Hi,
I am currently developing an nRF54L15 module.
During the evaluation, I measured the Tx current consumption and got a result that was 2mA higher than the value listed...
Hi
I am trying to setup and test the OpenThread CSL feature on nrf52840DK with OpenThread daemon and RCP mode nrf52840DK.
I found there is a way to build the Daemon for...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine if we can use one Ignion antenna, shared for the LTE and GPS.
On the original...
I can flash the chip. I can run the debugger. I can go to the connected devices, select the device, go to the little "plug" symbol on the RTT, and select it. That brings up...
Hi all,
we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
