Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I am using Ubuntu 16.04 (64-bits) OS.
I installed JLink_Linux_V620b_x86_64.deb and was using nRF5x-Command-Line-Tools_9_6_0_Linux-x86_64.tar
I can capture the...
Hi,
I use SES import my keil project, and my keel project work well. With SES, i meed a problem, that is , i have a global variable like this:
uint32_t g_ulMainLoopCounter...
Nordic51822 no external 32.768 k of crystals in the routine what configuration
Use this routine
nordic\nRF5_SDK_12.2.0_f012efa-3d\examples\ble_peripheral\ble_app_bps\pca10028...
When I am stepping through my application code crashing at
memset(&cccd_md, 0, sizeof(cccd_md));
"Setup information:
IDE: Using IAR
Device: nRF52832
Soft...
I'm using the NRF51822 for a project that will be powered by a lithium battery. I'm wondering if it would be safe to use a diode ( such at this one ) to drop the 4.2V LiPo...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello,
For BLE, there is always an ACK in link level no matter it's write/read/notify/indicate.
How about 2.4G proprietary mode? Is it possible to just send a data without...
Hello,
I am using the nrf52832 with SDK v12.3 and PCA10040. Not using any soft devices, nor the RTC. The program is intended such that timer0 is set to toggle a pin (P0_11...
Hi,
We are working on Automotive project using nrf51824. below are some queries ,
We are basically want to use the chip as a Bluetooth to Kline(using Uart) bridge ....
Hi,
we would like to start a new product (update a design) and add Apple Homekit feature because ""Apple will now allow any registered developer to start building a HomeKit...
As i am new in embedded programming,I was trying to connect MPU 9250 with nRF52 DK by using given examples. now it is showing error
#error "No MPU defined. Please define...
i'm new in BLE, now i have project with nrf51822 and sdk 11.0.
in chip arm like STM, MPS or PIC, avr. when byte come, we have a flag set 1 to notice that there is one byte...
Hello,
Is there any way to check if the bluetooth is connected after NVIC Reset?In our project when we get a specific command from the UART, NVIC reset is done.After the...
