I am using an nRF52840 USB dongle to sniff some Zigbee packets for a product I am developing. I am trying to use Wireshark to decode the messages shared. I followed the steps...
Hi,
I have set up a destination in the the NRF Cloud Message Routing Service
The destination has been verified and I can successfully send the test message from NRF Cloud...
Hi,
I was looking at integrating a speaker in my design and i have a class d amplifier that takes in an analog signal which i want to feed directly from the chip. I wondered...
Hello,
I am using SDK v2.9.1 for a Bl653 (NRF52833) and was trying to use the Nordic Academy Example for how to setup the SPI bus. The Nordic Academy example states we must...
I'm currently working on configuring the nPM1300 used in our custom board. In the product spec v1.2, it supports 2 USB compliant current limits, IBUS at 100mA and IBUS at...
Hi,
I am currently trying to enable the GPIO output interrupt functionality on my nPM1300ek with an STM32. However, I am unable to get it work correctly(I was only able...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hi ,
Am using NRF52 ,S132 SoftDevice
I have a simple Question, How can I know is any device already bonded or not to my peripheral ??
I need to show an option "Delete...
I am using nordic_sdk_10 with nrf51822 USB Dongle. I did a eraseall
flashed my softdevice and dfu bootloader and did a reset. Now i can see advertisement report DFU_Targ...
I am using a custom board with NRF51822-QFAC-R7 and Master Control panel on Android. The DFU is working with test images from SDK130.
BL : examples/dfu/bootloader/hex/dfu_dual_bank_ble_s130_pca10028...
Hi all,
I have been trying to get my Nordic nRF51822 transmit continuously on a particular channel for FCC certification. The Test lab wants me to test the product in 2402MHz...
Dear Forum Users,
I am trying to send the data in a burst. Thanks to this post I have managed to achieve ~2,5 kB/s. However this lasts only for few seconds. Then the stream...
When i load the example radio_test pca10040 in Keil i get the following error messages
Error #544: Required Software Pack 'ARM.CMSIS.4.5.0' is not installed
Error #544:...
Hello
I plan to use two Bluefruit LE Micro devices that contain the nrf51822 as BLE beacons.
I also plan to use a BLE receiver (on another arduino) to receive the beacons...
Hi,
I'm using GCC with SDK11 on linux. I'm able to build successfully. When I try to run "make flash" or "make flash_softdevice", I get error nrfjprog command not found...
I just got the nrf51822 evaluation kit. I followed the instruction and installed everything per instruction. When I tried to open “Blinky” project, I am getting the following...
Hello,
I have a peripheral based on the nrf52 that connects to my Android phone already in direct advertisement mode.
I am trying to get a NRF52 central working with...
Hello! I'm trying to use the PWM on a board containing an nRF51822 device. However, simply including the nrf_pwm.h file multiple errors are trigered, such as the following...
Hi everybody !
I try to use nrf52 DK with OSX
I follow this link
devzone.nordicsemi.com/.../
and I have a problem with this step :
launchpad.net/.../ download
...
hi,
i tried to make a ac dimmer circuit controlled with dc
i use nrf51822
this is my dimmer circuit
aaand this one is zero crossing detector
finally this...
