Help Needed: BLE Not Working on nRF52810 (Tried Zephyr & nRF5 SDK)
Hi everyone, I really need help getting BLE working on my custom board with the nRF52810 . I've been trying...
Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hello LE-Audio team,
By any chance, do you have a working code base that supports a headset with 2 end points instead of just one as your sample nRF5340_Audio kit?
If...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
Hi,
I am storing data using pstorage module but when i power off my nrf51-dk board, the contents get deleted and not retained in memory. What could be the reason for that...
Hi,
For a new design with nRF51822-QFA, planning to use Johanson Balun and Chip antenna as shown in attached diagram. Not using any tuning components between Balun and...
Hi,
I was wondering why DFU_IMAGE_MAX_SIZE_BANKED is calculated as
(((DFU_REGION_TOTAL_SIZE/2) - DFU_APP_DATA_RESERVED))
and not
((DFU_REGION_TOTAL_SIZE - DFU_APP_DATA_RESERVED...
Hi, I'm using ble_app_uart application from latest nRF52 SDK on IAR compiler 7.1 and PCA10040 board.
It loads and runs debug code, but it does not add breakpoints on any...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Heading ##Here my PCA1000 board is getting detected in nRFgo studio even i can program and debug it, But i cant see COM PORT.
Can anybody help me out in this...
When i...
Hi,
I'm trying out the nRF52832 with kit PCA10040 V 0.9.0. I have S132 softdevice installed and running the ble_app_pwr_profiling example from nRF5 SDK v11.0.0.
I'm...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
I am trying to manage the bonds as follows. I've defined the max bonded masters as 4 on my slave. When this list gets full, I delete a random bonded master on the slave (not...
I'm trying to flash to a device with the GCC toolchain using "make -f Makefile flash_softdevice" and nrfjprog fails with the message "ERROR: There is no debugger connected...
Hi.
I've searched this forum and also the code for pin muxings. One of post here said that any gpio can be configured for any output. However how is this done in code?...
I have a peripheral device based on the nRF51822, s130 and SDK 11.0.0. It's designed to only ever have one central device to which it's bonded. Out of the box, without a bond...
Hello.
I have a question.
I want to use UART without flow control.
In this case, I don't know what to set rts_pin_no and cts_pin_no of app_uart_comm_params_t.
Please...
