Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hi,
Everyone,
I found out on that ble_app_power_profiling application is developed for Lower power current consumption....as It keeps system in the system_off_mode until...
Hi,
I am trying to measure and minimize current consumption .....
Following previous question on this forum,I found way to measure current on NRF51 DK by cutting SB9....
Hello Everyone..
i am new to nrf52 and this community.
i am using nrf52 and android master control pannel.
in my code i define my custom uuid base to ..
//430Cxxxx...
Hi, I'm looking for an easy way to use the UART in blocking mode (or something similiar) with a receive buffer that is filled in background:
If possible using EasyDMA...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi everybody
I am making a custom board which using ANCS (nrf51 sdk 9.0.0, softdevice 110 ver8.0.0). I saw on the original code have button_led_init() function to initiate...
hello,
I've encountered a problem with our own nrf51822 circuit not advertising.
Our circuit is exactly the same as what is given as the reference circuitry on the datasheet...
It's the first time i'm using the spi to connect various slaves, so is there any example how to communicate a raspberry with 2 or more nRF24L01 on the same bus?
Thanks in...
Today I have recieved the new nRF52 Development kit PCA10040. I did a update for the nRFgo Studio to version 1.21.2.3.
The softdevice s132_nrf52_2.0.0 will be flashed without...
OS: Windows 10
Target: nRF51-DK
Tried to connect with nrf51-dk with Keil MDK-Lite v5.18a.
The default Jlink version used along with this IDE was v4.98e
the 'download...
Hello all,
I'm looking at the example projects and ble_app_template in particular, and have noticed something that doesn't seem to make sense...
In main(), this project...
Hi, I am looking for a Bluetooth Low Energy Soc based solution like nRF51822, but I'd like to have an open source firmware solution...
Do you have that kind of solution...
Hi
I want to execute my app from the RAM to test if i'll get a considerable decrease in the current consumption.
I'm using : "s130_nrf51822_0.9.0-1.alpha" &"nrf51822QFAC...
Hi
I'm trying to change TX power and measure the current consumption while advertising, (DC/DC disabled) and i get an increase of 3.44mA from 0dbm to 4 dbm. Ok That's logic...
