I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hi,
I have 2 pins with PULL_UP in sense mode and when i use sd_power_system_off() i measure 25mA current, which is higher than when my system is on (around 10mA)!!
How...
We are using an nRF8001 with bonding. We are trying to figure out how big the dynamic data is that we need to store (since we are used a fixed-size storage in flash memory...
I just received my Beacon Kit and need a programmer/debugger but money is tight. These are the options I'm looking at:
cut the traces on my nRF51822 EK board and add...
I wrote an application that works using an Enhanced Shockburst-compatible protocol (because I need it so), using the RADIO interface.
What happens if a packet with an address...
Hi U guys
First I’m pretty new I use of bluetooth low energy, so bear with me.
It is pretty simple, I need to send a temperature each 10 sec. or whenever it has changed...
Hello. The nRF51822 Series Reference Manual says on page 38, "The SWDCLK pin
has an internal pull down resistor and the SWDIO/nRESET pin has an internal pull up resistor...
Tunning connection parameters to minimize current consumption for a fitness device transmitting data to ANT+ and BLE at 1sec intervals.
The desire is timeout after 60sec...
Hi,
We are trying to use the over-the-air bootloader in our application.
Our problem is the bootloader seems to require one first over-the-air download before it allows...
Which pins are mapped as ADC inputs for the NRF51822? I've pored over the documentation, but I can't seem to find which ADC pins (AIN0 to AIN7) correspond to which GPIO pins...
Hi
My aim is to be able to update the application code OTA in a 128kb chip (version nRF51822 QFABB0). First, I want to use the nordic original code to discard any other...
Hello all -
I'm trying to learn about the db discovery module from the perspective of the BTLE central and I'm a little confused by the client architecture. The SDK documentation...
I'm developing an application for a device which needs to support DFU service,
If my device get the specific packet over BLE (like 0xd1), i want to start dfu service. ...
I'm trying to study Message Sequence charts under the BLE GAP (Generic Access Profile) section of the s110 soft device.
However, I've noted that multiple links don't seem...
Hi
I'm studying at university and working on my thesis.
What I'm doing with a remote control and I want to measure the impedance of the antenna, because I want to be documented...
