Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hello,
I would like to develop an application that makes photos using a small camera from the omnivsion series and send the data via Bluetooht, using the nRF51822. These...
Hi,
I got the error message when programming the nRF24LE1 :
"An error occurred when programming the nRF device. The infopage seem to be broken"
and also "The infopage...
Hello,
I am trying to create my own design using an SMA edge Antenna, and I am very closely following the Altium Design files provided by Nordic for PCA10005.
I have...
Hi,
I have a case where the receive end event is triggered even though the receive base address and prefix shouldn't match. Some background:
Initially the receiver is...
I am working with the nRF51822 S110 and having trouble implementing SPI. In other devices' SPI protocols, MISO can be held high until the device is ready to transmit data...
I'm uising the NRF51822 PCA100001 eval kit. I'm trying to open a couple uVision 4 projects in uVision 5. Unfortunately, it keeps telling me to install the software pack. I...
Hey,
I am designing a custom PCB with the nrf51822. I would like to use the reference layout that Nordic provides, specifically nrf51x22_qfaa. My project involves reading...
I have recently started using the new rev 3 parts with 32K of SRAM and I was wondering what the timeframe is for the softdevice to take advantage of the extra memory?
My...
I would like to understand when I would need a wired programming (with help of TC2030 connector) interface and when I would need OTA. I am trying to find the easiest and fastest...
Hi,
What is the difference between using WFE and sd_app_evt_wait to force the processor into sleep mode?
We're trying to optimize for power consumption, and somehow...
I have experimengted with prepared write on Nordic 130 softdevice and found it's quite
low performance in terms of throughput.
First, between iOS/Android device and Nordib...
Hi Nordic's experts
We got a RF problem in certification test, attached picture is the measured occupied bandwidth, the value of OBW is 1.73MHz , but the guy in the lab...
Hi,
Does anyone known what the maximum frequency is that the timers can operate on ?
I want to count a signal that is 24Mhz while the clock frequency is only 16Mhz.
So...
Hi :)
In my program, just ONE pipe to use advertising service data is not enough. There is the function:
lib_aci_open_adv_pipes(const uint8_t * const adv_service_data_pipes...
