Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am writing an App for the Central/Master side using the s130 v1.0.0 SD. I am connecting to the soft device using the python wrappers for the nRF51-BLE-Driver-Win 0.5.0....
I want to write a program in Keil by SPP for communicating with a thermal printer that uses SPP
but I can't find source code about that.
Is this possible to do this with...
Hello
i have nrf52 PAC10036 dev Board.
i am using the visualgdb.
when i try to create the instance of the TWI.
i got the error
please check image for detail.
How i can...
I want to turn off BLE-peripheral Advertising for 8 hours but I want to use another timer with period of 50ms to scan GPIO ,
when I change prescale of
APP_TIMER_INIT(APP_TIMER_PRESCALER...
Hello,
is there a good documenation or introduction about the Programmable Peripheral Interconnect Feature? I read the short part in the Objective Product Specification...
Hi everyone,
I need to use an nRF51822 (MBH7BLZ07-109033) mounted on a custom board.
I want to develop my firmware application on the custom board in such a way I can...
Hello,
I am using nrf51822 doing projects. I met an issuse which is that at the first 6 minutes, it can normaly go into UART interrupt and run subroutine successfully....
I'm testing out TWI on pins 24/25 and I get a crash when I attempt to do a TWI transfer and I find myself in: WDT_IRQHandler ()
I'm using much of the example code:
APP_TWI_INIT...
Hello, I have a few nRF devices, and I am unsure as to which revision the ICs are. Here are the three HWIDs:
0x00AE,
0x0086, and
0x0077
I tried looking into the nRF51_Series_Compatibility_Matrix_v2...
Hi,
I need to sample 2 inputs at 200Hz and send it on an app. Can I send the data at this speed using UART service? I was trying to do it using HRM example but could not...
Hi, I am trying to compile the code
github.com/.../main.c.
I need to include the header file uart_confg.h, can someone tell me where I can find it in the sdk 10 component...
Hi,
I wrote a program that uses ESB communication between two nodes. On both sides I use the same ESB configuration and the same ESB init function, the difference is only...
Hello,
Environment: nRF51DK + SDK8
We've developed the beacon application but the advertising interval is set to 5 seconds. The beacon can be discovered by nRF Connect...
I have searched here on the DevZone, and also around the web, and don't see this issue mentioned elsewhere. I really appreciate any help finding a solution.
I tried following...
