I'm evaluating the nRF93M1-DK for a Linux-based host system. I'm trying to get ECM/RNDIS to carry the data session, but I am having trouble setting it up.
The AT command...
Problem Description
The custom hardware board cannot boot normally after flashing the firmware. However, the exact same firmware image works perfectly on the official nRF54L15...
Hello, I am raising this issue because I am working with multiple devices doing CS procedures between each other and I found a limitation. I am working with NCS 3.3.1. When...
For my project I want MCUboot with the upgrade image placed in the external flash, and TF-M. I am not able to get this combo to boot however, and I suspect the reason is that...
Hi!
I am trying to do a DFU with external flash, using a nRF54L15-DK development kit.
To evaluate this feature, I use the l9_e3_sol example available on GitHub (I use...
Hi, I'm experiencing flash write issues on an nRF54H20 DK's on-board NOR flash. I'm using ncs and toolchain v3.3.0.
Setup: the on-board MX25UW6345G on EXMIF, using the jedec...
hello! I'm having problem when trying a repairing after clearing the bond information in the nrf52840 i using pairing via oob , i exchange oob between nrf52840 and RPI using...
With the SDK_11 s130 ble_app_gls on nRF51-dk, i am able to pair and bond with the board with Android 6.0 as central. But if the user forget the paired device on the android...
Good morning,
would it be possible for a Nordic RF specialist to review our antenna design? Preferably we would upload our Altium-based layout for your review.
Thank...
I want to connect a beacon to my android app and I want to know how to make a development environment (I am using eclipse). Can you show me show examples ?? where can i get...
Hello,
the FDS_VIRTUAL_PAGES is set to 3 in all examples which use the Peer Manager module. The parameter's comment says
Number of virtual flash pages to use. One...
Hello,
I am completely new and I am having NRF52 series.
I would like to know is there an ready example for android or iOS phone using Bluetooth:
Control volume...
I programmed my nrf51822 with one the hex sample files that are existed in the nordic package. toolbox app can find my beacons but cannot connect to them and with nrf connect...
Hi all
The nRF51822 product specification V3.2, chapter 8.8, specifies the times t_CSD and t_CC of the SPI slave peripheral for the low power mode and for the constant...
I've experienced some struggles programming for Taiyo Yuden's EYAGJNZXX board. According to the user manual provided its chip is nrf51822 (which supposedly works with s210...
Hello.
I have a question.
I use nrf52 & Keil.
I want to get data from sensors and send it with BLE.
Now, I found sample codes.
It uses UART and sends with BLE.
...
HI,
I want to send an "Echo" command to the nRF8001 using an ATMEGA328. Can some one suggest code for it ? How should the command be coded in a packet ?
Regards
Hey,
currently I use nrf_gpio_pins_set() and and nrf_gpio_pins_clear() from nrf_gpio.h to set and clear specific GPIO ports, respectively. If I want to change the current...
Alright, I have searched high and low and been unable to find a simple answer to this question. It must be possible for the nrf51 to launch Siri on an iPhone, I have seen...
Hi!
I'm doing an Arduino .txt file sending project using the nRF24L01+. But i'm quite a noob in this so i'd like a bit of advice.
I'm using an Arduino Uno, and I made...
Hello,
while reading some nrf5 examples, I've stumbled over a pattern in the examples, where the result code of a function is stored in variable (most of the time named err_code...
