Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi !
I'm working with the pca10040 and nRF5_SDK_11.0.0_89a8197.
I tried to run the DFU bootloader example with SEGGER Embedded Studio 2.2 ( following this tutorial ).
...
"I need to analyse,what is the array of hex values corresponds to.
#define SETUP_MESSAGES_CONTENT {\ {0x00,\ {\ 0x07,0x06,0x00,0x00,0x03,0x02,0x41,0xfe,\ },\ },\
0x07...
Hi all,
BACKGROUND:
I'm working on a project where we use the nRF51, and our first prototype boards just arrived.
So I've made some power measurements trying to calculate...
Hi,
Currently i am using ble app uart as a reference example and nus service with soft device S130 for our project. I want to use multi role example (central and peripheral...
Hi !
I'm trying to run the BLE bootloader example ( here ). I succesfully programmed the SoftDevice and the DFU bootloader :
The device start in bootloader mode ...
Hi, few days ago when I attach the nRf51-DK and try to read the content, the nrfgo software freezes or crashes.
If it freezes i can see clearly the content stack of the...
Does anyone know what's the maximum acceptable input timeout_ticks of function
uint32_t app_timer_start(app_timer_id_t timer_id, uint32_t timeout_ticks, void * p_context...
Hello,
I really need the ability to switch between different advertising messages. Could you please (please!) add a callback after an advertising message has been sent...
We are using the NRF board to act as node.
Samsung Galaxy S6 device is being used as the Router. We are trying to ping the node using ping6 command.
The issue is that the...
I have a working peripheral NUS application to pair/bond by entering passkey in the nrf master toolbox android application.
Now i want to replace the mobile witha nrf 51822...
nrf51822bluetooth low energycode 10
twiddle gravatar image
twiddle
1
asked May 9 '16
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just...
Hello Everyone,
I am designing the prototype using NRF51822 and i have choosen the DC DC power mode but the real problem is most of the time my radio will be sleeping so...
I have nRF52 Development Kit (PCA10040). I'm using Keil uVision.
I want to measure RSSI of some beacons and if the signal is strong then send MAC of this beacon over UART...
Hello Everyone
I'm trying to debug ble_app_beacon project, having the following error when trying to launch the debug session:
Error in final launch sequence Error executing...
