Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Hi,
With the following program running, how can I achieve the lowest power consumption between timer events:
nRF Timer is running with the HF crystal requested
...
51822, config a pin as output , in the param , set disconnect or connect the input pin, when config as output ,what mean disconnct/connect input pin?
I use a pin to light...
For my project to simulate the spreading of a disease I am thinking of recording the complete social network on the beacons and then collecting the data to a pc. I have roughly...
I am using nRF51-DK hardware and working on the ble_uart_app s130 SDK_11
Upon power-up, nRF51 is discoverable and connectable. After sometime, it is no longer discoverable...
Hi, I am using microESB library. We want to test the continuous carrier wave mode for ESB(similar to using DTM for BLE continuous carrier wave mode). Is there any library...
Hi,
I have the nrf52 working perfectly in iBeacon mode. Even when my iPhone is Off, the iPhone will wake up and post a notification with UUID, Major,Minor etc.. It's great...
I have suspended my Beacon in SLEEP (at .5 uA) until a keypress. Is there an event that can trigger an event if there is a low voltage detection while in SLEEP?
My goal...
hello,
I am trying to write one characteristics on GATT server from a client. My server program (acts as peripheral) is working fine with MCP. But when i am trying to connect...
Hi,
I've spent the last few days trying to get this going and getting super frustrated.
After having no luck getting the nrfutil to work on Python ( another thread ...
HI,
I am using micro esb(0db tx power, 250kbps, RX mode) from GitHub( github.com/.../nrf51-micro-esb) . I am using nrf51822xxaa and SD10.0 and s130. With just the micro esb...
I can't get the Master Control Panel to work. I think the drivers might be messed up but various re-installs aren't having any success.
Can you suggest some troubleshooting...
I'm Dinesh Katkar, trying to adapt
new IoT design and development and planning to build wearable device based on nRF52832 Bluetooth SoC chip and ordered nRF52 Development...
Hello,
I am new to all this RF stuff. I am trying to set up multiple transmitters (2 for now) and one receiver. Basically, each of two transmitters read one set of data ...
hi all,
i am currently using version 8 sdk.
i tried to include bsp_init() function in my code.
i attached following header files
#include "nrf51.h"
#include <stdbool...
