I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
I noticed that having the UART enabled on my application in a NRF52 (SD132, SDK 11.0.0) takes a lot of current consumption. If I completely disable any UART support on my...
I want to design a BLE enabled display panel, which is a general purpose panel leverage all kinds of resources from mobile phone, including sensors, interaction, network,...
Since Nordic offers BLE sniffer tools including its hex code, I would like to flash it to my own USB dongle as a test. I insepected the hex code, and found its address starts...
Hi All,
I am new to the nRF processors (but not new to embedded progarming). Trying to use the evaluation board with the examples on the SDK. After realizing the freeware...
Q0. What IRQ Priority does BLE Has? and also what IRQ Priority does UART can have?
I'm guessing that from s130's document P65, Exception Model, It says,
Softdevice Timing...
Hello,
I could not set breakpoint in Eclipse. I set CFLAGS to -O0 and -g3 in Makefile
I am using GNU Tools ARM Embedded 6 2017-q1-update and Eclipse Neon3
Below are...
Hi,
is at the moment possible with S110 (nRF51 SDK) to whitelist only SOME of bonded peers? I need to allow connection from one selected central. Selection is made by user...
As a follow up from devzone.nordicsemi.com/.../ , I am now trying to find out if I am getting all of the memory settings put together correctly. When I have them at higher...
I am using nrf51822, 16K RAM, 256K Flash.
From the movie , there is no way to secure my firmware for DFU. Is there any other way to secure my firmware?
Thank you
I know the many differences coming in bt5. Will the programming concepts be the same in the upcoming 5 version? IF my code is working with ble4.1 will it automatically work...
After a bunch of headache I was able to successfully program with the nRF51822 Development Kit without the nRFgo Starter Kit motherboard, here is how I did it.
Hardware...
I'm working on a design that incorporates an nRF52832 along with some sensors and drivers.
Up to this I've been sacrificing power consumption in prototypes by using LDOs...
Hello,
Is it possible to change SPI baud rate whenever we want?
For example:
The initial SPI baud rate is set to 4M. We want to change the baud rate to "2M" to get...
Hi,
This may be stupid, but I can't declare classes in my .h file in keil. I have arduino library for my I2C device, but keil; does not recognize when I declare classes...
I've looked through and tried many examples on getting my SAADC to produce a temperature offset. About a month ago I had the SAADC working really well with a wheatstone bridge...
