Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I'm new to using the Nordic SDK and I'm trying to use the BLE template to start my own service. Is there a walk-through for doing this somewhere that may be able to help?...
Hello,
I'm developing a simple code that make use of timers using NRF-based boards and Arduino code.
The following code works fine on a Simblee nRF51822 board , but...
I was trying to install firmware into my nRF51 Dongle using jlink.exe on Windows, so I can use nRF Sniffer. I made the mistake of unplugging the dongle from USB after erasing...
I have an nRF52832, coding with SEGGER and the SDK 14.2.0. I'm trying the ble_peripheral/ble_app_uart example (although I get similar results with the other BLE examples)...
Using a pushbutton while advertising, the GPIOTE_IRQHandler handles the pushbutton click OK, but then the processor resets. The RESETREAS is code 4, aka. RESET from soft reset...
Hi,
I have couple of queries that need to be sorted,
http://www.nordicsemi.com/eng/Products/S112-SoftDevice, Says that S112 supports 2-peripheral connection and 1 broadcaster...
I want advertise the peripheral periodically only. i implement the logic it is working fine.but my doubt is once i connected to connected to central device advertise is no...
Noted the difference between the layouts concerning antenna matching among DK 0.9 and DK 0.11.
DK 0.9
DK 0.11
The screenshots are for L3. Differences between...
Hello,
I have a requirement to implement the following functionality. Can this be done?
Basically i need to store some customer info on the NFC NTAG. This has to customizable...
I am using nRF Connect for desktop v2.3.0. In my DIS service Firmware Revision String characteristic I am using a string of 30 characters. But when I connect to my device...
Hi,
We are looking into developing a device based on 52832 platform.
How many devices (phones) can be paired with our device?
In other words: How many pairing keys can...
See attachment - enlarge if it's too small. How can I get nRF Connect on my Windows 10 laptop to bring more than 20 characters, and also print in text (instead of hex values...
I would like to know the part number for the Side facing RGB LEDs used in the Nordic Thingy 52. I couldn't find the Bill of Material for the Thingy 52.
Hi. I got TCA6424A IC which communicates through i2c. I tried to use that with nordic but it doesnt respond. I used simple twi scanner application which should print address...
