Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Dear All,
Currently I'm developing a BLE module that will be useful by its uart service and will use nrf51822. Nordic provided an example based on sdk 6.1 for low power...
Hello,
I want to read data from mesh network (from all the servers) to send it to a gateway. I saw in the documentation that Provisioner s can be a part of gateway devices...
Hi all,
I'm trying to enable Bluetooth 5 extended advertisement in nRF52840.
Currently, I'm using Nordic SDK v15.0.0 and S140 Softdevice v6.0.0.
In order to init the...
Dear Nordic Support Team,
I want to send the new PCB layout for manufacturer but I am not sure that
I can use any pairs of pin for DFU over serial or not.
I want to...
Hi all,
I have a question regarding the BLE mesh specification. When you are transmitting data using advertising frames, how does it check if the transmission medium is...
Hello everyone,
I am working on DFU bootloader application for android and iOS (using Qt C++).
For android everything works fine, but for iOS I have problems.
In order...
for the mass production what is the best solution in order to flash the nRF52?
for the mass production can I use DK PCA10040 ?
The DK PCA10040 can be used for dubbug on...
Hi I'm using Keil MDK 4.7 with nRF5 SDK V15, both of the 2 SDKs are installed at C:\, and the Keil4 Nordic License has been installed. When I tried to compile one of the example...
Hi all,
Is there any possibility to intimate any documentation errors(spell mistakes, content doubts, etc) to nordic documentation team?
Thanks,
Sridhar
Hi,
I have used examples\dfu\secure_bootloader\pca10056_ble application and successfully updated two applications(heart rate and health thermometer) over BLE. In order to...
Hello, i' trying to measure the power consumption of the nrf52840 PDK. So far i have been able to measure the current. How can i go about measuring the voltage and is it constant...
Hello, I recently received a Thingy:52 and was able to connect to PC using J-Link. After uploading Heart Rate Monitor program Thingy is no longer able to be added using iOS...
Hi,
I am facing difficulties porting Mesh examples to IAR.
I am getting the following error : #error "Your compiler is currently not supported." during compilation from...
I'm working with nrf52 dk to read the sensor dht22. i need to follow this steps to make sure the sensor is ready to send data.
Wait until DHT responds and pulls the line...
