after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
Here is a newbie question:
I have NRF52832 (sparkfun breakout board) and ADT7410 temperature sensor and, I want to create a data logger. But, i could not understand...
Hii all,
Is there any one started using and succeed with nRF connect 2.0, I installed and open this app, and added two apps two this
After that I launched the app...
hii team,
iam trying to pair my central app with one peripheral device which is generating random passkey while pairing .when central (my App) is sending pairing request...
Hi,
I am using the pin change interrupt example provided in the SDK examples. By setting the input sense to NRF_GPIOTE_POLARITY_LOTOHI, the interrupt handler is called...
Hello, i am a beginner, i have a doubt that my UART project is building without the softdevice being flashed and the output is not seen on the pins. I wanted to configure...
Hello
I want to change the mac address of my device from normal mode to random mode,
I do not know how this does for nrf52832 (NRF52-dk)
Thank you in advance for your...
Hi All,
I've got a nRF51-DK development kit, and I just compiled and downloaded my first example to it through Keil uVision. Problem is that nothing happens when the program...
Would it be advisable for system design to use CAN(CAN Open) and BT simultaneously on nRF52832 IC?
Why this bothers me is because capabilities of nRF BT MCU's are growing...
Is it possible to limit the connection duration on BLE peripheral (nrf52832)? For example, if central is in connection for more than X seconds, then peripheral terminates...
hello everyone,in my code, SDK9.0 uart ,please tell me the reson if you the book of knowledge
static void timers_init(void)
{
uint32_t err_code;
APP_TIMER_INIT...
I am looking at the att_mtu_throughput example in the blog ( devzone.nordicsemi.com/.../)
Some of the items in configuration menu that are shown in video and listed in...
Hi,
I am using sdk13 with a nrf52832 dev kit.
I have two separate projects one with a bootloader and other with an application.
I use the following configuration in the...
Hello,
I am using nRF51822 and an STM32 communicating over UART. I want to test UART communication without CTS and RTS so I did the configuration as shown below:
static...
I've been using the NRF24L01 transceiver to wirelessly broadcast data back and forth among 4 devices, where each device contains the NRF24L01 chip. Everything works great...
