What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I'm having trouble porting my project from the older SDK (2.6.0) to the new SDK.
I thought the most straightforward way to do that would be to start with a sample project...
Dear Nordic Team,
I was trying to use the I2C peripheral on the nRF5340 with clock speed of 1MHz, but I kept getting the error "unsupported speed". I was using the function...
Hello! This is the third time I'm asking something about the same project, but I'm running into problems one after the other.
The current problem is this - the hogp object...
I am using NCS v2.9.1 and trying to enable a bootloader chain with NSIB and MCUboot. The regular setup works fine, however if I try to enable the minimal configuration, I...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I am using nrf5340 audio DK,
The project I use is v3.0.2 .\samples\nrf5340\empty_app_core\. If the board target is nrf5340 audio DK
a compilation error will occur. build...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
Hello DevZone,
It seems that the nRF 52840 DK has 1MB of internal flash memory and it can be extended by external memory via QPSI. I have found External Memory source where...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hello at all, I try to compile the example peripheral_uart for the nrf54L15-DK. The goal is to compile without west. My directory structure:
where I copied everything from...
Hi all,
I'm working on a custom board based on the nRF9160 and using nRF Connect SDK v3.0.2. We’ve developed the board in-house and integrated the npm1300 PMIC as part of...
Hi all,
I have attached one external antenna to my initiator device and one to my reflector, both devices being nrf 54l15 dk and the antenna are connected to the SWF connector...
I am using nrf5340 audio DK. After plugging it into the computer, 3 VCOMs and RTT will appear. What are these three ports? docs.nordicsemi.com/.../logging_nrf5340.html Here...
