Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hello, I am trying a simple btle application where one mcu will send a "help" message and another will respond with its address. The mcu that asks for stores the address of...
Hello,
I would like to implement the nordic DFU protocol natively in a new app as I have historically found it tiresome and buggy to turn the DFU program into a library...
Hello, I am using eclipse app development, to achieve OTA function, use Maven to download DFU library, can not find the library, see your introduction： compile'no.nordicsemi...
I have a BLE circuit utilizing an NRF52832 cpu/integrated radio, necessary impedance matching network and a single ended micro-strip "L" antenna. How can I determine the gain...
I an trying to wake the chip and record the temperature readings when temperature reaches a certain threshold (eg: 80 deg C), can this be achieved using built-in temperature...
I debug the DFU Bootloader through UART,I am sure the APP code is complete updated,but the application does not run when the device is after bootloader to auto soft reset...
Hello:
I'm trying to get an example program ble_app_hrs running on my custom board, because earlier last month I couldn't write the cccd descriptor properly and I suspect...
i try to connect and read and write on my device with ionic2 BLE plugin , i can connect and also write on the device but when i try to read a data from device and use startNotification...
Dear team,
Our customer using "nRF51422 Development KiT8PCA10028)" with "ble-sniffer_nRF51822_1.0.1_1111_Sniffer.hex".
They can check advertising packets, but, they...
Hello,
Here is a newbie question:
I have NRF52832 (sparkfun breakout board) and ADT7410 temperature sensor and, I want to create a data logger. But, i could not understand...
Hii all,
Is there any one started using and succeed with nRF connect 2.0, I installed and open this app, and added two apps two this
After that I launched the app...
hii team,
iam trying to pair my central app with one peripheral device which is generating random passkey while pairing .when central (my App) is sending pairing request...
Hi,
I am using the pin change interrupt example provided in the SDK examples. By setting the input sense to NRF_GPIOTE_POLARITY_LOTOHI, the interrupt handler is called...
Hello, i am a beginner, i have a doubt that my UART project is building without the softdevice being flashed and the output is not seen on the pins. I wanted to configure...
Hello
I want to change the mac address of my device from normal mode to random mode,
I do not know how this does for nrf52832 (NRF52-dk)
Thank you in advance for your...
