How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Dear team,
Our customer using "nRF51422 Development KiT8PCA10028)" with "ble-sniffer_nRF51822_1.0.1_1111_Sniffer.hex".
They can check advertising packets, but, they...
Hello,
Here is a newbie question:
I have NRF52832 (sparkfun breakout board) and ADT7410 temperature sensor and, I want to create a data logger. But, i could not understand...
Hii all,
Is there any one started using and succeed with nRF connect 2.0, I installed and open this app, and added two apps two this
After that I launched the app...
hii team,
iam trying to pair my central app with one peripheral device which is generating random passkey while pairing .when central (my App) is sending pairing request...
Hi,
I am using the pin change interrupt example provided in the SDK examples. By setting the input sense to NRF_GPIOTE_POLARITY_LOTOHI, the interrupt handler is called...
Hello, i am a beginner, i have a doubt that my UART project is building without the softdevice being flashed and the output is not seen on the pins. I wanted to configure...
Hello
I want to change the mac address of my device from normal mode to random mode,
I do not know how this does for nrf52832 (NRF52-dk)
Thank you in advance for your...
Hi All,
I've got a nRF51-DK development kit, and I just compiled and downloaded my first example to it through Keil uVision. Problem is that nothing happens when the program...
Would it be advisable for system design to use CAN(CAN Open) and BT simultaneously on nRF52832 IC?
Why this bothers me is because capabilities of nRF BT MCU's are growing...
Is it possible to limit the connection duration on BLE peripheral (nrf52832)? For example, if central is in connection for more than X seconds, then peripheral terminates...
hello everyone,in my code, SDK9.0 uart ,please tell me the reson if you the book of knowledge
static void timers_init(void)
{
uint32_t err_code;
APP_TIMER_INIT...
I am looking at the att_mtu_throughput example in the blog ( devzone.nordicsemi.com/.../)
Some of the items in configuration menu that are shown in video and listed in...
Hi,
I am using sdk13 with a nrf52832 dev kit.
I have two separate projects one with a bootloader and other with an application.
I use the following configuration in the...
Hello,
I am using nRF51822 and an STM32 communicating over UART. I want to test UART communication without CTS and RTS so I did the configuration as shown below:
static...
