Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi.
I'm using NRF Connect v1.0 on a Windows 10 PC, together with an nRF52-DK (PCA10040).
It works nicely with the connectivity firmware 1.0.0 that the PC app offers to flash...
Hello, I'm looking into this particular issue and are now having some concerns. Namely:
My firmware size currently stands at 30k. It's not big, but definitely not...
Hi
I set the attribute request when receive a notify
case BLE_ANCS_C_EVT_NOTIF:
m_notification_latest = p_evt->notif;
notif_print(&m_notification_latest...
Hello, we are working on a project where we use the nrf52836 with a BMX055 sensor.
Due to BLE, we have to use a softdevice.
For now, we are using this version of the sdk...
Is there such a thing? For ultra-low, harvested power, how do you recommend powering the nRF5x: load switching Vcc or leaving Vcc connected and hold the reset pin low until...
Hello,
I have got the nRF52840-PDK, and I usually use CrossWorks, so I spun up a new project based on SDK 13, examples\peripheral\blinky and flashed this using default...
I would like to connect n antennas (through RF switch) to a single nRF52 that would do phase comparison between the n received signals. This is something related to I/Q sampling...
I know it is a pretty basic question but I can't manage to understand the documentation enough to pass the tutorial predeterminate code. If someone could help and tell where...
Hi,
I am trying to write a program which send data through notification. All is working, excepted that once the notifications are done, the device automatically disconnects...
I have an advertising device (NRF52DK+SD132_V3.1.0+SDK_12.2.0) where I whitelisted an address corresponding to my NRF51 Dongle (0xDA509C569622).
While the dongle is initiating...
Hi, At the moment I am using nRF Toolbox to upload DFU *.zip files to our devices. We have been finding that the devices will become unresponsive after a firmware upload,...
Hi!
I have trouble in flashing a simple nrf51822 via the nrf51-dk.
Can anyone ensure me that this simple wiring should be able to upload an hex file onto the nrf51822...
The Peer Manager is currently in experimental state and is not recommended for production and same for the device manager for some sdk.So which SDK should be preferred
