Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Good afternoon we are updating some Nordic chips but to make the connection work it is necessary to install the modem version 1.3.1 wait for it to connect and then install...
Hello,
I need two signals with a phase shift to control my motor. For some reason, completely randomly, sometimes my GPIOTE event is not triggered and i get the inversion...
Hi All,
Based on nRF52832 SDK14.2 rtc example, I want to change it to retrigger RTC Compare0, let the LED1 also toggle every 3s, instead of keeping LED1 on. I tried to add...
Hi, guys, I have an IR receiver module with 3 pin (AX-1838HS) ?
How can I use it on my nrf52832 ? I have PCA10040 development board. I don't know how to connect them and...
I need to drive a stepper motor without software intervention, since strict timing is a must.In the following image you can see the required wave-forms - the motor requires...
The SD API (S132-6.0.0) documentation provides little beyond what one could guess from the function and type names. sd_mutex_acquire says "Attempt to acquire a mutex". nrf_mutex_t...
Hi i am doing a prosject to get notification on cell phone when i get mail in my postbox (postbox outside the house) I am using a nRF51 dongle, and want it to connect to cellphone...
Hi! I'm working on HID mouse example on SDK 13.0.0. I'm supposed to use this as a low power media button control. I've done a few modicifations on the code for power optimizations...
I know that few companies choose to use NRF528001 with a separate microcontroller like Fitbit.
I would like to know why would they do so instead of using an NRF52 chip that...
Hey,
I am using a nRF8001 with a STM32L051 as an application controller.
After resetting the nRF the RDYN pin goes low, as expected. Then I'm setting the REQN line LOW...
Hello all,
I have a Nordic Thingy 52 board, and I have download the Thingy 52 SDK, I can debug it successfully.
But after I debug it , or download it, the board runs with...
We have an application with FreeRTOS. If we do not initialize softdevice, the freertos interrupts tend to come in at a very very slow rate. I know that softdevice does clock...
nRFgo Studio displays a "Enable reset pin" option on the nRF52 DK but does not display this option on our custom hardware; we use a Segger J-Link for programming the custom...
Hello,
I would like to know the CALIBRATEOFFSET function in detail.
Could you disclose the part of source code on this CALIBRATEOFFSET function?
Best regards,
Kiyoshi...
