I made a custon pcb and until now it is working as expected . I am using the me54l14 module by minewsemi and i want to enable the CTE capabilities so that i can have angle...
Help Needed: BLE Not Working on nRF52810 (Tried Zephyr & nRF5 SDK)
Hi everyone, I really need help getting BLE working on my custom board with the nRF52810 . I've been trying...
Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
I have been using NRF51822 for some time as BLE chip with services.
For some debugging reasons I need a faster stream method...
I looked at Gazell and found it simple to...
Hi, I have a question about this memory layout .
At Figure 2 (of the memory layout), it erases the previous application.
After that, at step 1, it says that the firmware...
Hello,
i have a BLE device running with a service with three writable characteristics. At the moment I have one data handler function.
If there is any characteristic written...
When I try putting any breakpoint on my code to watch some variables, Keil will never halt that breakpoint. When I click pause in the debug session, the disassembler shows...
I added the DFU service to my project.
I will get this error: #5: cannot open source input file "ble_dfu.h": No such file or directory
This error appears in the dfu_app_handler...
Hello all,
I have migrated a project that was working well (on custom hardware) in Keil to gcc/Eclipse. I followed all the instructions on this site:
https://devzone...
Hi,
I've recently moved my development environment from Windows + Keil uVision to Linux + ARM GNU Toolchain . I'm able to build and flash the application firmware, but...
Hi all,
The DK board and sample code no longer produces cursor movement on Win7.
Using the nRF51DK board, Keil 5.14, S110 V7.1. Previously, I had the HID mouse sample...
Hello Nordic Community,
i have the following issue, im using a Nordic Nrf51422 in proprietary mode. On my RSA i can see that before the paket sending begis the radio sends...
Today, I tried out the Ble Bootloader from the Sdk examples.
As a central client, I'd used the »nRF Loader App« an an iPhone and also »nRF Mcp« on an Android Tablet.
I...
Hi,
from Keil uVision I need to debug/program nrf51822 in my application which uses 1.8 V. I guess nrf51 DK is not capable of doing this (it supports only 3 V targets). What...
Hi,
I have a reset issue when trying to set a delay greater or equal to 100 milliseconds using nrf_delay_ms(...). This only happens if I start my app timers (app_timer_start...
Hi,
I am trying to generate a 128Hz sine wave using the nrf_pwm library . First I tried this with SD110 enabled but ran into some problems that turned out to be a known...
Hi,
I'm going through the errata and a few of them look serious that the developer kit might be useless for some of us if we want to use it for any realistic testing (I...
