Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi everyone,
I am using the following:
*nRF51422
*SDK11
*keil uVision 5.17
*s130
I have been working with nRF51 that scans beacons and stores it into persistent...
Hello everyone,
I am trying to set the security parameters for bonding with PASSKEY (static)format it is getting executed very well(connected and bonded) for the SDK 9...
Dear all:
My device uses LDO mode and DC-DC mode respectively, and the distance is different.In 4dbm, the distance of the LDO mode is 110m, while the LDO mode is in the 70m...
Hi,
I was wondering if anyone could clarify why there are enable, set and clear (CHEN, CHENSET, CHENCLR) for the PPI channels when according to the data sheet they all...
I checked S130 document for using nRF51822.
I want to change the nRF51822 like the following mode.
peripheral => central => scanning => peripheral => central => scanning...
Hello
I am trying to change the ticks value of Battery measurement interval (ble_app-prox example) but i am not able to understand how the ticks period is measured based...
Hi,
I was seeing memory leak issues when using NRF51 with JLkink v4.98. See this link:
forum.segger.com/index.php
This issue has been fixed with the latest version of...
The address miss event is not shown as a transition in Figure 22 of the NRF51 Reference Manual. What state does the NRF51 enter upon an address miss and how long after the...
To use BEL application, the soft device must be downloaded before programming.
i can find a table shows that which soft device version is suitable for chip version.
how...
Our application is developing RC units for small (indoor) model airplanes - we want to be able to have multiple planes flying at once without "stepping" on each other.
...
I'm developing a NUS-based peripheral and adding a timeout to force a disconnect after a period of inactivity (i.e. no incoming NUS data). However my peripheral also provides...
Hi all,
I'm trying to use Ant+ HRM RX demo profile from nRF51_SDK_10 ( nRF51422 ) between my board PCA10028 and a Garmin rate sensor but I get some trouble.
Let me explain...
In the example iOS app and the DFU service in the firmware there is a DFU revision characteristic UUID 0x1534. The Nordic SDK documentation don't mention this characteristic...
HI，I'm having trouble in flash operation.I I did an experiment of flash operation.I call pstorage_store( ) or pstorage_load( ) very second after nrf51822 connected with app...
