Hi,
nRF5340 and SDK v3.0.0 I'm using.
Currently my nRF5340 based BLE device can be bonded with smartphone via passkey, after bond is done, the device stops advertising...
hi everyone
After using Android nRF Connect FOTA, the settings storage partition of my device was erased, which means that my device's PAIR information was lost and the...
Hi Nordic Team,
I'm looking to use the UICR->OTP region ( One Time Programmable (OTP) memory region within the User Information Configuration Registers (UICR)) on the nRF54H20...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Due to production requirements, I need to obtain the device's QR code. However, I found that the QR code can only be retrieved using the code snippet below after calling Nrf...
Hi Nordic Support Team,
I'm currently experimenting with Channel Sounding using a couple of nRF54L15 boards.
I am trying to obtain raw I and Q samples so that I may analyze...
Hello,
currently i am configuring the networking stack on my project.
The goal is to use Matter's built-in Thread connection, to establish a Secure CoAP connection. I...
SOC: nrf52840
SDK: v2.9.0
Device is a central, it connected to 16 peripherals, these peripherals will power on 90 seconds and then power off 10 seconds(one cycle). ...
Further into development of the ReRAM file system. I noticed that in generated DTS for nRF54L15 board for the ReRAM we have:
What is the reason for providing erase-block...
I am trying to compile hci_lpuart for thingy91_nrf52840, but I have these issue. hci_lpuart:
Any ideas on how to solve this? I'd really appreciate it. And if you have any...
Hello, we are trying to receive BLE extended advertisement pakcets from Thingy53 using a nRF52840DK as a HCI controller with a Raspberry Pi 5. I am using a nrf52840dk as a...
Hi, I have to integrate on my MQTT application , location library using GNSS. Actually I am using location library on cellular. I want to use exclusively GNSS. I am developing...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Dear Nordic Engineering Team,
I am currently developing a wireless ECG acquisition system based on the ADS1298 analog front end (AFE), the nRF5340 SoC, and the nRF7002 Wi...
I am building the: https://academy.nordicsemi.com/courses/cellular-iot-fundamentals/lessons/lesson-2-cellular-fundamentals/topic/lesson-2-exercise-2/ exercise and as part...
So I will have 2x physical UART provided on my board. I am using printk(), and I want to choose which UART handles console traffic by config options.
How to achieve that...
Im trying to rotate my st7789v 240x240 display with LVGL commands. Im using nRF5340.
My .dts
My code:
But this dont make any change on my rotation.
Someone...
Hello all,
I am having issues with the configuration of the FEM nRF21540 on the costum board Fanstel BT840NE with the Enhanced ShockBurst (ESB) protocole.
We are not able...
Hi,
I'm trying to run the Lesson 4 Exercise 2 solution from the Nordic DevAcademy BLE Fudamentals course (origin/v2.9.0-v2.7.0) run on a nRF54L15 PDK board.
I'm currently...
Hi,
I configured for using security BT_SECURITY_L2 for a device that I had previously configured for using BT_SECURITY_L4. When I try to connect with an Android phone that...
