HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Hi, I am using:
SDK v15 with nRF52840 chip running in soft device s140. I am Using Segger Embedded studio.
I want to update a application( Say Blinky) thorugh DFU. I perform...
Hi, I'm using Atomic_FIFO library and for my application I need to know the number of elements currently in the fifo, the library itself doesn't provide any functionality...
Hi,
The program will crash when spi transfer on NRF52810. The crash occurs in spim_xfer function, immediately after spim_int_enable function calling,
but if i remove the...
Hi,
nrf5_SDK_for_Mesh_v2.0.0_src
When complete provision a provisionee , provisioner will assign provisionee a mesh key and device key.
Now i want to know how to calculate...
I can get a clean build and working product with some workarounds, but a couple issues remain from migrating sdk 13.1 to sdk 15.0 (SES nrf52832 s132).
1) After nrf_drv to...
Hi,everyone.
I had learn for below Links and compiling is no error.
https://devzone.nordicsemi.com/f/nordic-q-a/26448/nrf52832-maximum-number-of-central-links/104063#104063...
Hi,
I'm having problems to run the Loopback example in the Bluetooth Mesh SDK:
infocenter.nordicsemi.com/index.jsp
I'm receiving a timeout.
My setup is as follows...
This is a duplicate of https://devzone.nordicsemi.com/f/nordic-q-a/35127/spi-master-0-uses-300ua-upon-first-transfer but I wanted to be safe because I pre-maturely verified...
Hi,
I have been working on MPU9250 examples given in here .Though the program runs fine in KeilUvision 5, the output in tera term shows only 0,0,0 for Accelerometer values...
Normally one writes 0 to an event register to reset it.
I am writing a uart driver and when I open my interface I want to prime my transmit pump by setting EVENT_ENDTX to...
Hi all,
What are the default preflashed contents in the out of box nrf52840 flash?
I assume that bootloader is not present. If my assumption is correct how preflashed...
I'm looking at the SDK15 I2S example project using DMA. My dev set up is 52840/Keil.
The project is under: \nRF5_SDK_15.0.0_a53641a\examples\peripheral\i2s
In the callback...
I am new to BLE development, if that helps preface this question.
My goal is to get a BL652 module by Laird working with the BLE UART example from the Nordic SDK. I am using...
We are working on porting an MESH example from Segger to IAR.
We started with the BLE Peripheral Template, and pulled all the code for the light_switch_provisioner into...
