Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi,
I am using nrf54l15 ,here I have bare i2s code for reading data from mics and ble code for notifying that data but here I am planning to use lc3 codec to compress data...
I have just purchased nRF54L15 DK, run Quick Start and programmed 'Hello World', but the verification failed and nothing happened. I opened the serial terminal, but nothing...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
I want to add nrf21540 fem support in our nrf54l15 based application. I am currently using nrf54l15dk and nrf21540EK to achieve this.
Below is the .overlay and prj.config...
Dear all,
I am wondering, what is the reason for C13 being 3.9pF for QFN package, while there is no capacitor on WLCSP reference design? Could we use like 10nF instead?...
I'm following the tutorial Exercise 1 – Custom board for single-core SoC using ncs v2.9.0 with one slight difference in that I'm using a nRF52DK with nRF52832 because that...
Hello,
I am running firmware on a custom board toting an nrf5340 with NCS version 2.3.0. There is also a Micron 8Gb NAND flash on board that I have a custom driver for....
Hello,
I'm currently working with the channel_sounding_ras_initiator project on the nRF54L15 DK , using the nRF Connect SDK from the latest main branch on GitHub ( nrfconnect...
Hi.
For a while I have had some issues with the toolchain when using the nRF connect SDK in visual studio code on windows 10. I believe it was after installing SDK version...
Hello~ I used the ot-nrf528xx codebase for compilation, and according to the content in the readme, I compiled two Hex files for USB and SPI interfaces using the USB_trans...
I used nRF24L01+ in an industrial control project that requires low power consumption. I have completed all the functional development and reliability verification. A problem...
Hi, the nordic team
I am working on thread protocol using SDK version 2.9.1.
I use the SED device,My poll is 1000 ms. How can I receive messages from my parent node when...
How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hello,
Hopefully this will be a quick(ish) one since I think I found the answer, but just need confirmation.
To preface (My setup):
nRF9151DK
Modem firmware: mfw_nrf91x1_2...
