I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
IUsing the Master Control Panel application on my Android device to connect to my nRF51822 module (acting as the GATT server), I have implemented the Device Manager (v10 SDK...
I have successfully compiled BLE application using tutorials provided on nordic website.
but when I start doing debugging for better understanding find out that I can not...
Hey,
We got a problem when trying to figure out how to detect the custom services from Unity. We are trying to read data and afterwards to do some manipulations of objects...
I want send ble bond connection request from raspberry pi to nrf51882.
Can you please let me know which ble libraries I need to send central ble bond request to nrf51882...
Hi,
I try to modifie ble_multilink example et send more than one data,
here is my main code code :
static uint8_t test[4] = {0x41, 0x42, 0x43, 0x44};
static...
Hello,
SPIS is adding a 350uA from 80uA baseline running current. I would like some tips and advise on improving this. Thanks!!!
The baseline operation consists of:...
I am using eclipse as IDE , but when i build ble_app_hrs example it's getting an error ../../../../../../components/ble/ble_advertising/ble_advertising.c:195: undefined reference...
I have a 32u4 Feather but don't get the right support from Adafruit to create my own Profile. I have downloaded Nordic's android app and can see all the characteristics on...
Hi.
I'm trying to enable and disable softdevice repeatedely.
In my code, softdevice is firstly enabled then advertising properly.
After some seconds, softdevice is disabled...
Hi,
I used the ble_peripheral and ble_central example and I send messages from one to the other.
Know I need to do the same with multilink.
I managed to connect ble_multilink_central...
hi dear Engineers!
the questions is it possible to use RX RF reciever to estimate the average BW RF signal input power like I do it in Semtech 433/868 RF SoC to make desicion...
hi, all
my nrf52832 can not run good when download the program into the flash, and can not run good in debug session mode without breakpoint ， but if I add one breakpoint...
Hi,
I am trying to send L2CAP connection reply by using this "sd_ble_l2cap_ch_conn_reply()",but i am unable to see the packet on wireshark. The incoming connection handle...
Hi I note here that it is recommended to apply solder mask to the ground layer beneath the nRF24L01+ exposed die so they don't connect:
devzone.nordicsemi.com/.../
But...
I'm finding a discrepancy with numbers between the nwp_008 whitepaper (quarterwave printed monopole antenna for 2.45ghz) and AppCad values.
I've assumed you can measure...
Hi.
Months ago I loaded the nfc_url_record example and it worked fine.
Later some time I updated the packages, and since then that particular example gives errors.
The...
Hi,
Anyone familiar/experiened in production-test gear for BLE?
Test sets, i.e. LitePoint, Anritsu, USRP, NI?
What's relevant to test, i.e. output power...
Figure 222 of the OP spec states "important: no components in bottom layer". Are you recommending that we keep the bottom side clear under/near the nRF52840? This feels a...
I met some problems in testing ECDH , the project is the example in E:\Source\NRF52832\nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs...
