Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
I suffer from the phenomenon which can't sometimes maintain communication between the 32.8ms at Gazell communication at present.
When not writing in SoftDevice, this...
Hi,
I am using " BLE-Gateway " example from nRF51-ble-bcast-mesh to advertise my custom "Manufacturer Data" from 1 nRF51422 device to another nRF51422.
I've made the...
I have been able to implement the PER test (on nRF51822) using the direct_test_mode_s110 and code based off the example python code from the nAN34 zip file. I adjusted to...
Hi,
I want write a demon running on linux to control the 51822 dongle to connect or disconnect with mobile phones.
Now I have one idea, which is using string as command...
Hello,
I need to send packets that are larger than 20 bytes to once characteristic with a variable length. When I set the variable length to 100 bytes, the Attribute table...
NRF51822 supply voltage is 3V battery. When I design principle diagram, I have a question.
Both AVDD and VCC_nRF are connect with the battery's positive?
While trying to get the SDK's bootloader working with gcc, I have to replace some ARMCC-speific code found in bootloader_util_arm.c:
__asm void StartApplication(uint32_t...
I am using the nRF51-DK and have Timer1 setup as follows:
void start_timer(void)
{
NRF_TIMER1->MODE = TIMER_MODE_MODE_Timer;
NRF_TIMER1->TASKS_CLEAR = 1;
NRF_TIMER1...
Hi Guys,
I am currently using the ble driver for windows (Python) to get notifications from two Gatt services (Same Service/charac/descriptors/etc basically same application...
I've just trying to get SPI working, everything is compiling OK but when initialising the SPI, when the line below is hit,
/* Clear waiting interrupts and events */
p_spi_instance...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
I would like to support app_button, however I need to configure a pin as NOPULL and trigger on a low to high transition without debouncing.
I don't see a way this can co...
HI,
We survey APPLE's ANCS right now! But we have a question that need your help.
I use ios device ios 8.3,ble softdevice 8.0
I have some questions about the pairing...