after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
What should I add to the makefiles to be able to generate an assembly code? Something similar to what is seen in the debug mode of Eclipse. I have tried -S/s but it...
Hi
I want to porting to nRF52840 but since S140 SoftDevice Specification documentation doesn't exist
I can not proceed with porintg.
I need S140's detail memory map...
I am using s132_nrf52_3.0.0_softdevice.hex and sdk12 and compiling with arm-none-eabi-gcc. The problem is that the bluetooth set up just jams at:
// Enable BLE stack.
...
I'm trying to get my nRF52 BLE peripheral to connect to my phone while its screen is off and it's in sleep mode. Other consumer BLE peripherals that I have can connect to...
Hello
is this possible to reset the timer.
for example i set the timer for 10 Second.
when he reach up to 5 second then i would like to reset the timer.
i found no function...
Hi,
I just noticed that my PTX and PRX projects use different assemblers and linkers -- not sure why. I got the sample projects from Nordic. What's the difference between...
I built my project on ble_app_uart peripheral example from SDK 12.2 and have added a display (Sharp LS044Q7DH01) using nRF52 as a SPI master to communicate. I think I have...
I have used NRF52840 and SDK 13.0.0. Module SPIM.
Library does not support buffer size more then 8 bit.
But I try write to register TXD.MAXCNT and I can't write value more...
Hi
I'm interfacing MMA8452Q with nrf51822 using TWI all read-write function working fine but when I try to read acceleration data nrf_drv_twi_rx & nrf_drv_twi_tx function...
I am porting our sdk 8 based firmware for the sdk 11. Now the code crashes at the code below:
err_code = sd_ble_gap_device_name_set(&sec_mode,
(const uint8_t *)name,...
We followed the instructions for the beacon example for nrf 52 dk.
Multiple attempts to change and reset the board, there was no change in the ad packet.
Can someone...
I'm using the nRF52832 chip without an external crystal. I configured it to use the internal RC with:
nrf_clock_lf_cfg_t clock_lf_cfg;
clock_lf_cfg.source = NRF_CLOCK_LF_SRC_RC;...
